参数资料
型号: MC3PHACVFAE
厂商: Freescale Semiconductor
文件页数: 19/36页
文件大小: 0K
描述: IC MOTOR CONTROLLER 32QFP
标准包装: 250
应用: AC 电机控制器,3 相
输出数: 1
电源电压: 4.5 V ~ 5.5 V
工作温度: -40°C ~ 105°C
安装类型: 表面贴装
封装/外壳: 32-LQFP
供应商设备封装: 32-LQFP(7x7)
包装: 托盘
产品目录页面: 808 (CN2011-ZH PDF)
Operation
Standalone Application Example
Figure 12 shows an application example of the MC3PHAC, configured in standalone mode. Resistor
values and jumpers have been selected to provide the following performance:
1. Base frequency of 60 Hz and positive PWM polarity (from Table 3 )
2. PWM frequency resistor 3.9 k ? , which implies 10.582 kHz from Table 4 ). (5v/(3.9k + 6.8k))*3.9k =
1.82 volts
3. Dead-time resistor = 5.1 k ? , which implies 4.5 μ s (from Figure 9 )
4. Fault retry time resistor = 8.2 k ? , which implies 32.8 seconds (from Figure 10 ).
5. Voltage boost resistor = 12 k ? , which implies 25.5 percent (from Figure 11 ).
6. The wiper of the acceleration potentiometer is set at 2.5 V = 64 Hz/second acceleration rate (from
the Acceleration Control description on page 11 .) The potentiometer, in this case, could have been
a resistor divider. If a resistor divider is used in place of the acceleration potentiometer, keep the
total resistance of the two resistors less than 10 k ? . Always use 4.7k ? in series with the center of
the acceleration voltage divider resistors, connected to the ACCEL (pin 27) as shown in the
application example, Figure 12 .
7. Crystal/resonator capacitor values are typical values from the manufacturer. Refer to the
manufacturers data for actual values.
PC Master Software Operation
Introduction to PC Master Host Software
The MC3PHAC is compatible with Freescale ’s PC master host software serial interface protocol.
Communication occurs over an on-chip UART, on the MC3PHAC at 9600 baud to an external master
device, which may be a microcontroller that also has an integrated UART or a personal computer via a
COM port. With PC master software, an external controller can monitor and control all aspects of the
MC3PHAC operation.
When the MC3PHAC is placed in PC master software mode, all control of the system is provided through
the integrated UART, resident on the MC3PHAC. Inputs such as START, FWD, SPEED, ACCEL,
MUX_IN, and PWMPOL_BASEFREQ have no controlling influence over operation of the system. Even
though the SPEED, START, and FWD inputs are disabled while the system is in PC master software
mode, through PC master software, it is possible to monitor the state of those inputs.
The most popular master implementation is a PC, where a graphical user interface (GUI) has been
layered on top of the PC master software command protocol, complete with a graphical data display, and
an ActiveX interface. Figure 13 shows the MC3PHAC configured in PC master software mode. It is
beyond the scope of this document to describe the PC master software protocol or its implementation on
a personal computer. For further information on these topics, refer to other Freescale documents relating
to the PC master software protocol and availability of PC master host software.
MC3PHAC Monolithic Intelligent Motor Controller, Rev. 2
Freescale Semiconductor
19
相关PDF资料
PDF描述
ZXBM1016ST20TA IC MOTOR CTRLR 1PH TSSOP20
VI-J1W-EZ-S CONVERTER MINIMOD DC/DC 5.5V 25W
EEU-FR1J391 CAP ALUM 390UF 63V 20% RADIAL
AMIS30623C6238RG IC MOTOR DRIVER/CTLR 20SOIC
PX0840/A/2M00 CABLE PLUG IP68 USB A-B 2M
相关代理商/技术参数
参数描述
MC3PHACVP 制造商:Freescale Semiconductor 功能描述:MCU 8BIT HC08 CISC 8KB FLASH 5V 28PDIP - Rail/Tube 制造商:Freescale Semiconductor 功能描述:Controller IC
MC3PHACVPE 功能描述:马达/运动/点火控制器和驱动器 8BIT MCU 8K FLASH OTP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MC3S12C128 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller
MC3S12C32 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller
MC3S12C64 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller