参数资料
| 型号： | MC3PHACVPE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | IC MOTOR CONTROLLER 28-DIP |
| 标准包装： | 13 |
| 应用： | AC 电机控制器，3 相 |
| 输出数： | 1 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 28-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 28-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 808 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Operation
Operation
The MC3PHAC motor controller will operate in two modes. The first is standalone operation, whereby the
MC3PHAC can be used without any intervention from an external personal computer. In standalone
mode, the MC3PHAC is initialized by passive devices connected to the MC3PHAC and input to the
system at power-up/reset time. In standalone mode, some parameters continue to be input to the system
as it operates. Speed, PWM frequency, bus voltage, and acceleration parameters are input to the system
on a real-time basis.
The second mode of operation is called PC master software mode.That operational mode requires the
use of a personal computer and PC master software executing on the personal computer, communicating
with the MC3PHAC, or a microcontroller emulating PC master software commands. All command and
setup information is input to the MC3PHAC via the PC host.
Standalone Operation
If the VBOOST_MODE pin is high when the MC3PHAC is powered up, or after a reset, the MC3PHAC
enters standalone mode. In this mode of operation, the functionality of many of the MC3PHAC pins
change so that the device can control a motor without requiring setup information from an external master.
When operated in standalone mode, the MC3PHAC will drive certain pins corresponding to parameters
which must be specified, while simultaneously monitoring the response on other pins.
In many cases, the parameter to be specified is represented as an analog voltage presented to the
MUX_IN pin, while certain other pins are driven low. In so doing, the MC3PHAC can accommodate an
external analog mux which will switch various signals on the MUX_IN pin when the signal select line goes
low. All signals must be in a range between 0 V and V REF . As an economical alternative, an external
passive network can be connected to each of the parameter select output pins and the MUX_IN pin, as
The Thevenin equivalent impedance of this passive network as seen by the MUX_IN pin is very important
and should be in the range of 5 k ? to 10 k ? . If the resistance is too high, leakage current from the
input/output (I/O) pins will cause an offset voltage that will affect the accuracy of the reading. If the
resistance is too low, the parameter select pins will not be able to sink the required current for an accurate
reading. Using a pullup resistor value of 6.8 k ? (as indicated in Figure 8 ), the resulting value for each
parameter as a function of the corresponding pulldown resistor value is shown in Figure 9 , Figure 10 ,
The START input pin is debounced internally and a switch can be directly accommodated on this pin. The
input is level sensitive, but a logic 1 level must exist on the pin before a logic 0 level will be processed as
a start signal. This will prevent an accidental motor startup in the event of the MC3PHAC being powered
up, where the switch was left in the start position.
The FWD input pin is debounced internally and can directly accommodate a switch connection. The input
is also level sensitive.
operation, one and only one jumper connection can be made at any given time. Table 3 shows the polarity
and base frequency selections as a function of the jumper connection.
MC3PHAC Monolithic Intelligent Motor Controller, Rev. 2
16
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MC44604PG | IC REG CTRLR FLYBACK PWM 16-DIP |
| MC44605PG | IC REG CTRLR FLYBK ISO PWM 16DIP |
| MC44608P75G | IC REG CTRLR FLYBK ISO PWM 8-DIP |
| MC7810ECDTX | IC REG LDO 10V 1A DPAK |
| MC7818CD2TR4G | IC REG LDO 18V 1A D2PAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC3S12C128 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12C32 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12C64 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12C96 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC3S12GC32 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:16-Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。