- 您现在的位置：买卖IC网 > PDF目录69024 > MC56F8006MLF (FREESCALE SEMICONDUCTOR INC) 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 PDF资料下载
参数资料
| 型号： | MC56F8006MLF |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| 封装： | 7 X 7 MM, 1.40 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, MS-026BBC, LQFP-48 |
| 文件页数： | 76/106页 |
| 文件大小： | 1215K |
| 代理商： | MC56F8006MLF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页当前第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页
Design Considerations
MC56F8006/MC56F8002 Digital Signal Controller, Rev. 4
Freescale Semiconductor
71
junction. The thermocouple wire is placed flat against the package case to avoid measurement errors caused by cooling effects
of the thermocouple wire.
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the interface between the case
of the package and the interface material. A clearance slot or hole is normally required in the heat sink. Minimizing the size of
the clearance is important to minimize the change in thermal performance caused by removing part of the thermal interface to
the heat sink. Because of the experimental difficulties with this technique, many engineers measure the heat sink temperature
and then back-calculate the case temperature using a separate measurement of the thermal resistance of the interface. From this
case temperature, the junction temperature is determined from the junction-to-case thermal resistance.
9.2
Electrical Design Considerations
CAUTION
This device contains protective circuitry to guard against damage due to high static voltage
or electrical fields. However, take normal precautions to avoid application of any voltages
higher than maximum-rated voltages to this high-impedance circuit. Reliability of
operation is enhanced if unused inputs are tied to an appropriate voltage level.
Use the following list of considerations to assure correct operation of the 56F8006/56F8002:
Provide a low-impedance path from the board power supply to each VDD pin on the 56F8006/56F8002 and from the
board ground to each VSS (GND) pin.
The minimum bypass requirement is to place 0.01–0.1F capacitors positioned as near as possible to the package
supply pins. The recommended bypass configuration is to place one bypass capacitor on each of the VDD/VSS pairs,
including VDDA/VSSA. Ceramic and tantalum capacitors tend to provide better tolerances.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND) pins are
as short as possible.
Bypass the VDD and VSS with approximately 100 F, plus the number of 0.1 F ceramic capacitors.
PCB trace lengths should be minimal for high-frequency signals.
Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance. This is
especially critical in systems with higher capacitive loads that could create higher transient currents in the VDD and
VSS circuits.
Take special care to minimize noise levels on the VREF, VDDA, and VSSA pins.
Using separate power planes for VDD and VDDA and separate ground planes for VSS and VSSA are recommended.
Connect the separate analog and digital power and ground planes as near as possible to power supply outputs. If an
analog circuit and digital circuit are powered by the same power supply, you should connect a small inductor or ferrite
bead in serial with VDDA and VSSA traces.
Physically separate analog components from noisy digital components by ground planes. Do not place an analog trace
in parallel with digital traces. Place an analog ground trace around an analog signal trace to isolate it from digital traces.
Because the flash memory is programmed through the JTAG/EOnCE port, SPI, SCI, or I2C, the designer should
provide an interface to this port if in-circuit flash programming is desired.
If desired, connect an external RC circuit to the RESET pin. The resistor value should be in the range of 4.7 k
–10 k;
the capacitor value should be in the range of 0.22 F–4.7 F.
Configuring the RESET pin to GPIO output in normal operation in a high-noise environment may help to improve the
performance of noise transient immunity.
Add a 2.2 k
external pullup on the TMS pin of the JTAG port to keep EOnCE in a restate during normal operation if
JTAG converter is not present.
During reset and after reset but before I/O initialization, all I/O pins are at input state with internal pullup enabled. The
typical value of internal pullup is around 33 k
. These internal pullups can be disabled by software.
To eliminate PCB trace impedance effect, each ADC input should have a no less than 33 pF 10
RC filter.
External clamp diodes on analog input pins are recommended.
相关PDF资料 |
PDF描述 |
|---|---|
| MC56F8323MFB60 | 0-BIT, 120 MHz, OTHER DSP, PQFP64 |
| MC68020CFC25E | 32-BIT, 25 MHz, MICROPROCESSOR, PQFP132 |
| MC68020CFC25E | 32-BIT, 25 MHz, MICROPROCESSOR, PQFP132 |
| MC6804J1P | 8-BIT, MROM, MICROCONTROLLER, PDIP20 |
| MC6805S3VP | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDIP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC56F8006VBM | 功能描述:数字信号处理器和控制器 - DSP, DSC DSC 32SDIP 16K Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MC56F8006VLC | 功能描述:数字信号处理器和控制器 - DSP, DSC DSC 32LQFP 16K Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MC56F8006VLF | 功能描述:数字信号处理器和控制器 - DSP, DSC DSC 48LQFP 16K Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MC56F8006VLF | 制造商:Freescale Semiconductor 功能描述:IC DSC 16BIT 16KB 32MHZ 3.6V LQFP-48 |
| MC56F8006VWL | 功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT DSPHC RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。