收藏本站
参数资料
型号： MC56F8006VLC
厂商： FREESCALE SEMICONDUCTOR INC
元件分类： 微控制器/微处理器
英文描述： 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP32
封装： 7 X 7 MM, 1.40 MM HEIGHT, 0.80 MM PITCH, MS-026BBA, LQFP-32
文件页数： 89/106页
文件大小： 1215K
代理商： MC56F8006VLC
Revision History
MC56F8006/MC56F8002 Digital Signal Controller, Rev. 4
Freescale Semiconductor
83
11
Revision History
Table 41 lists major changes between versions of the MC56F8006 document.
Appendix A
Interrupt Vector Table
Table 43 provides the 56F8006/56F8002’s reset and interrupt priority structure, including on-chip peripherals. The table is
organized with higher-priority vectors at the top and lower-priority interrupts lower in the table. As indicated, the priority of an
interrupt can be assigned to different levels, allowing some control over interrupt priorities. All level 3 interrupts are serviced
before level 2 and so on. For a selected priority level, the lowest vector number has the highest priority.
The location of the vector table is determined by the vector base address (VBA). Please see the MC56F8006 Peripheral
Reference Manual for detail.
By default, the chip reset address and COP reset address correspond to vector 0 and 1 of the interrupt vector table. In these
instances, the first two locations in the vector table must contain branch or JMP instructions. All other entries must contain JSR
instructions.
Table 41. Changes Between Revisions 2 and 3
Location
Description
Introduction on page 1
Added part marking for devices covered by this document
Section 6.7, “PWM, PDB, PGA, and ADC
Connections,” on page 38
Updated routing details for ANB24 and ANB25
Table 12 on page 42
Removed row about open drain mode (GPIO supports only push-pull mode)
Table 21 on page 47
Updated specifications for low-voltage detection threshold (high and low range) and
low-voltage warning threshold
Table 22 on page 51
Updated all Supply Current Consumption specifications
Table 26 and Figure 22 on page 55
Updated ROSC variation over temperature specifications (both ranges)
Table 31 on page 62
Removed I2C fast mode specifications and footnote about setup time if the TX FIFO
is empty (fast mode and FIFO not supported)
Appendix B on page 86
Added note explaining ADC and GPIO naming conventions
Table 44 on page 86
For I2C_SMB_CSR, clarified that bits 7 and 6 are reserved
Table 42. Changes Between Revisions 3 and 4
Location
Description
Throughout document.
Added information for 32-pin PSDIP device and devices with temperature range
from –40
C to + 125 C.
相关PDF资料
PDF描述
MC56F8006VLF 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48
MC56F8006MWL 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PDSO28
MC56F8006MLF 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48
MC56F8323MFB60 0-BIT, 120 MHz, OTHER DSP, PQFP64
MC68020CFC25E 32-BIT, 25 MHz, MICROPROCESSOR, PQFP132
相关代理商/技术参数
参数描述
MC56F8006VLF 功能描述:数字信号处理器和控制器 - DSP, DSC DSC 48LQFP 16K Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MC56F8006VLF 制造商:Freescale Semiconductor 功能描述:IC DSC 16BIT 16KB 32MHZ 3.6V LQFP-48
MC56F8006VWL 功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT DSPHC RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MC56F8006VWL 制造商:Freescale Semiconductor 功能描述:IC DSC 16BIT 16KB 32MHZ 3.6V SOIC-28
MC56F8006VWLR 功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT DSPHC RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*