参数资料
型号: MC68HC705V8B
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP56
封装: SDIP-56
文件页数: 10/172页
文件大小: 890K
代理商: MC68HC705V8B
MOTOROLA
SECTION 14: SERIAL PERIPHERAL INTERFACE
Page 96
MC68HC705V8 Specification Rev. 2.1
14.4
SPI IN STOP MODE
When the MCU enters the STOP mode, the baud rate generator which drives the SPI shuts
down. This essentially stops all master mode SPI operation; thus, the master SPI is unable
to transmit or receive any data. If the STOP instruction is executed during an SPI transfer,
that transfer is halted until the MCU exits the stop mode (provided it is an exit resulting from
a viable interrupt source). If the stop mode is exited by a reset, then the appropriate control/
status bits are cleared and the SPI is disabled. If the device is in the slave mode when the
STOP instruction is executed, the slave SPI will still operate. It can still accept data and clock
information in addition to transmitting its own data back to a master device.
At the end of a possible transmission with a slave SPI in the stop mode, no flags are set until
a viable interrupt results in an MCU "wake up". Caution should be observed when operating
the SPI (as a slave) during the stop mode because none of the protection circuitry (write
collision, mode fault, etc.) is active.
It should also be noted that when the MCU enters the stop mode all enabled output drivers
(MISO, MOSI, and SCLK ports) remain active and any sourcing currents from these outputs
will be part of the total supply current required by the device.
14.5
SPI IN WAIT MODE
The SPI subsystem remains active in wait mode. Therefore, it is consuming power. If it is
desired to reduce power, the SPI should be shut off prior to entering wait mode. A non-
resetexit from wait mode will result in the state of the SPI being unchanged. A reset exit will
return the SPI to its reset state, which is disabled.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料
PDF描述
MC68HC705V8FN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC68
MC68HC705V8CFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC68
MC68HC705X4CDW 8-BIT, OTPROM, 2.2 MHz, MICROCONTROLLER, PDSO28
MC68HC05X4CDW 8-BIT, MROM, 2.2 MHz, MICROCONTROLLER, PDSO28
MC68HC705X4DW 8-BIT, OTPROM, 2.2 MHz, MICROCONTROLLER, PDSO28
相关代理商/技术参数
参数描述
MC68HC706P6ACDW 制造商:Motorola Inc 功能描述:
MC68HC708MP16CFU 制造商:MAJOR 功能描述:
MC68HC711D3CFBE2 制造商:Freescale Semiconductor 功能描述:
MC68HC711D3CFN2 功能描述:IC MCU 2MHZ 4K OTP 44-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C,IrDA,LIN,SPI,UART/USART 外围设备:DMA,PDR,POR,PVD,PWM,温度传感器,WDT 输入/输出数:26 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN,36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND
MC68HC711D3CFNE2 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT