参数资料
型号: MC68HC711D3MP2
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PDIP40
封装: PLASTIC, DIP-40
文件页数: 148/157页
文件大小: 2252K
代理商: MC68HC711D3MP2
Serial Peripheral Interface (SPI)
Data Sheet
MC68HC711D3 — Rev. 2
90
Serial Peripheral Interface (SPI)
MOTOROLA
7.5 SPI Signals
This subsection contains description of the four SPI signals:
Master in/slave out (MISO)
Master out/slave in (MOSI)
Serial clock (SCK)
Slave select (SS)
7.5.1 Master In/Slave Out (MISO)
MISO is one of two unidirectional serial data signals. It is an input to a master
device and an output from a slave device. The MISO line of a slave device is placed
in the high-impedance state if the slave device is not selected.
7.5.2 Master Out/Slave In (MOSI)
The MOSI line is the second of the two unidirectional serial data signals. It is an
output from a master device and an input to a slave device. The master device
places data on the MOSI line a half-cycle before the clock edge that the slave
device uses to latch the data.
7.5.3 Serial Clock (SCK)
SCK, an input to a slave device, is generated by the master device and
synchronizes data movement in and out of the device through the MOSI and MISO
lines. Master and slave devices are capable of exchanging a byte of information
during a sequence of eight clock cycles.
Four possible timing relationships can be chosen by using control bits CPOL and
CPHA in the serial peripheral control register (SPCR). Both master and slave
devices must operate with the same timing. The SPI clock rate select bits, SPR1
and SPR0, in the SPCR of the master device, select the clock rate. In a slave
device, SPR1 and SPR0 have no effect on the operation of the SPI.
7.5.4 Slave Select (SS)
The SS input of a slave device must be externally asserted before a master device
can exchange data with the slave device. SS must be low before data transactions
and must stay low for the duration of the transaction.
The SS line of the master must be held high. If it goes low, a mode fault error flag
(MODF) is set in the serial peripheral status register (SPSR). To disable the mode
fault circuit, write a 1 in bit 5 of the port D data direction register. This sets the SS
pin to act as a general-purpose output. The other three lines are dedicated to the
SPI whenever the serial peripheral interface is on.
相关PDF资料
PDF描述
MC68HC711D3S 8-BIT, UVPROM, 2.1 MHz, MICROCONTROLLER, CDIP40
MC68HC711D3FN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
MC68HC711G5CFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84
MC68HC11G7CFN 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84
MC68HC711L6CFN1 OTPROM, MICROCONTROLLER, PQCC68
相关代理商/技术参数
参数描述
MC68HC711D3VFNE2 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC68HC711E20CFN2 功能描述:IC MCU 20K 2MHZ OTP 52-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C,IrDA,LIN,SPI,UART/USART 外围设备:DMA,PDR,POR,PVD,PWM,温度传感器,WDT 输入/输出数:26 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN,36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND
MC68HC711E20CFN3 功能描述:IC MCU 3MHZ 20K OTP 52-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C,IrDA,LIN,SPI,UART/USART 外围设备:DMA,PDR,POR,PVD,PWM,温度传感器,WDT 输入/输出数:26 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN,36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND
MC68HC711E20CFN4 功能描述:IC MCU 20K OTP 4MHZ 52-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN,SCI,SPI 外围设备:POR,PWM,温度传感器,WDT 输入/输出数:21 程序存储器容量:40KB(20K x 16) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC711E20CFU3 制造商:Rochester Electronics LLC 功能描述:8BIT, 20K EPROM, 768RAM. - Bulk 制造商:Freescale Semiconductor 功能描述: 制造商:Motorola Inc 功能描述: