- 您现在的位置：买卖IC网 > PDF目录4033 > MC8640DTHX1000HE (Freescale Semiconductor)IC DUAL CORE PROCESSOR 1023-CBGA PDF资料下载
参数资料
| 型号： | MC8640DTHX1000HE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 22/130页 |
| 文件大小： | 0K |
| 描述： | IC DUAL CORE PROCESSOR 1023-CBGA |
| 标准包装： | 1 |
| 系列： | MPC86xx |
| 处理器类型： | 32-位 MPC86xx PowerPC |
| 速度： | 1.0GHz |
| 电压： | 1.05V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 1023-BCBGA，FCCBGA |
| 供应商设备封装： | 1023-FCCBGA（33x33） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页
MPC8640 and MPC8640D Integrated Host Processor Hardware Specifications, Rev. 3
118
Freescale Semiconductor
System Design Information
designer place at least one decoupling capacitor at each OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren,
and VDD_PLAT pin of the device. These decoupling capacitors should receive their power from separate
OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren, and VDD_PLAT and GND power planes in the PCB,
utilizing short traces to minimize inductance. Capacitors may be placed directly under the device using a
standard escape pattern. Others may surround the part.
These capacitors should have a value of 0.01 or 0.1 F. Only ceramic SMT (surface mount technology)
capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren, and VDD_PLAT planes, to enable quick
recharging of the smaller chip capacitors. They should also be connected to the power and ground planes
through two vias to minimize inductance. Suggested bulk capacitors—100–330 F (AVX TPS tantalum
or Sanyo OSCON).
20.4
SerDes Block Power Supply Decoupling Recommendations
The SerDes block requires a clean, tightly regulated source of power (SVDD and XVDD_SRDSn) to ensure
low jitter on transmit and reliable recovery of data in the receiver. An appropriate decoupling scheme is
outlined below.
Only surface mount technology (SMT) capacitors should be used to minimize inductance. Connections
from all capacitors to power and ground should be done with multiple vias to further reduce inductance.
First, the board should have at least 10
× 10-nF SMT ceramic chip capacitors as close as possible
to the supply balls of the device. Where the board has blind vias, these capacitors should be placed
directly below the chip supply and ground connections. Where the board does not have blind vias,
these capacitors should be placed in a ring around the device as close to the supply and ground
connections as possible.
Second, there should be a 1-F ceramic chip capacitor on each side of the device. This should be
done for all SerDes supplies.
Third, between the device and any SerDes voltage regulator there should be a 10-F, low
equivalent series resistance (ESR) SMT tantalum chip capacitor and a 100-F, low ESR SMT
tantalum chip capacitor. This should be done for all SerDes supplies.
20.5
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. In general all unused active low inputs should be tied to OVDD, Dn_GVDD, LVDD, TVDD,
VDD_Coren, and VDD_PLAT, XVDD_SRDSn, and SVDD as required and unused active high inputs should
be connected to GND. All NC (no-connect) signals must remain unconnected.
The following list explains the special cases:
DDR—If one of the DDR ports is not being used the power supply pins for that port can be
connected to ground so that there is no need to connect the individual unused inputs of that port to
ground. Note that these power supplies can only be powered up again at reset for functionality to
occur on the DDR port. Power supplies for other functional buses should remain powered.
相关PDF资料 |
PDF描述 |
|---|---|
| MC7457RX1000NC | IC MPU RISC 32BIT 483FCCBGA |
| IDT7025S30J | IC SRAM 128KBIT 30NS 84PLCC |
| XC4020XL-3HT144C | IC FPGA C-TEMP 3.3V 3SPD 144HQFP |
| XC4020XL-3BG256I | IC FPGA I-TEMP 3.3V 3SPD 256PBGA |
| XC4020XL-3BG256C | IC FPGA C-TEMP 3.3V 3SPD 256PBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC8640DTHX1000N | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series |
| MC8640DTHX1000NC | 功能描述:微处理器 - MPU G8 REV2.1 0.95V -40/105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MC8640DTHX1067H | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series |
| MC8640DTHX1067N | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC8640DTHX1067NC | 功能描述:微处理器 - MPU G8,REV2.1,0.95V,-40 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
发布紧急采购，3分钟左右您将得到回复。