- 您现在的位置：买卖IC网 > PDF目录3943 > MC8640DTVU1000NC (Freescale Semiconductor)MPU DUAL E600 994-FCCBGA PDF资料下载
参数资料
| 型号： | MC8640DTVU1000NC |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 99/130页 |
| 文件大小： | 0K |
| 描述： | MPU DUAL E600 994-FCCBGA |
| 标准包装： | 1 |
| 系列： | MPC86xx |
| 处理器类型： | 32-位 MPC86xx PowerPC |
| 速度： | 1.0GHz |
| 电压： | 0.95V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 994-BCBGA，FCCBGA |
| 供应商设备封装： | 994-FCCBGA（33x33） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页当前第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页
MPC8640 and MPC8640D Integrated Host Processor Hardware Specifications, Rev. 3
70
Freescale Semiconductor
PCI Express
Maximum time to
transition to a
valid electrical
idle after sending
an electrical idle
ordered set
TTX-IDLE-SET-TO-IDLE
—
20
UI
After sending an electrical idle ordered set, the
transmitter must meet all electrical idle specifications
within this time. This is considered a debounce time for
the transmitter to meet electrical idle after transitioning
from L0.
Maximum time to
transition to valid
Tx specifications
after leaving an
electrical idle
condition
TTX-IDLE-TO-DIFF-DATA
—
20
UI
Maximum time to meet all Tx specifications when
transitioning from electrical idle to sending differential
data. This is considered a debounce time for the Tx to
meet all Tx specifications after leaving electrical idle
Differential
Return Loss
RLTX-DIFF
12
—
dB
Measured over 50 MHz to 1.25 GHz. See Note 4
Common Mode
Return Loss
RLTX-CM
6
—
dB
Measured over 50 MHz to 1.25 GHz. See Note 4
DC Differential
TX Impedance
ZTX-DIFF-DC
80
100
120
Ω
TX DC differential mode low impedance
Transmitter DC
Impedance
ZTX-DC
40
—
Ω
Required TX D+ as well as D– DC impedance during
all states
Lane-to-Lane
Output Skew
LTX-SKEW
—
500 +
2 UI
ps
Static skew between any two transmitter lanes within a
single link
AC Coupling
Capacitor
CTX
75
—
200
nF
All transmitters shall be AC coupled. The AC coupling
is required either within the media or within the
transmitting component itself. See Note 8.
Crosslink
Random
Timeout
Tcrosslink
0
—
1
ms
This random timeout helps resolve conflicts in crosslink
configuration by eventually resulting in only one
downstream and one upstream port. See Note 7.
Notes:
1. No test load is necessarily associated with this value.
2. Specified at the measurement point into a timing and voltage compliance test load as shown in Figure 52 and measured over
any 250 consecutive Tx UIs. (Also refer to the transmitter compliance eye diagram shown in Figure 50)
3. A TTX-EYE = 0.70 UI provides for a total sum of deterministic and random jitter budget of TTX-JITTER-MAX = 0.30 UI for the
transmitter collected over any 250 consecutive Tx UIs. The TTX-EYE-MEDIAN-to-MAX-JITTER median is less than half of the total
TX jitter budget collected over any 250 consecutive Tx UIs. It should be noted that the median is not the same as the mean.
The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed
to the averaged time value.
4. The transmitter input impedance shall result in a differential return loss greater than or equal to 12 dB and a common mode
return loss greater than or equal to 6 dB over a frequency range of 50 MHz to 1.25 GHz. This input impedance requirement
applies to all valid input levels. The reference impedance for return loss measurements is 50
Ω to ground for both the D+ and
D– line (that is, as measured by a Vector Network Analyzer with 50
Ω probes—see Figure 52). Note that the series capacitors
CTX is optional for the return loss measurement.
5. Measured between 20–80% at transmitter package pins into a test load as shown in Figure 52 for both VTX-D+ and VTX-D–.
6. See Section 4.3.1.8 of the PCI Express Base Specifications Rev 1.0a
7. See Section 4.2.6.3 of the PCI Express Base Specifications Rev 1.0a
8. MPC8640D SerDes transmitter does not have CTX built-in. An external AC coupling capacitor is required.
Table 49. Differential Transmitter Output Specifications (continued)
Parameter
Symbol
Min
Nom
Max
Units
Notes
相关PDF资料 |
PDF描述 |
|---|---|
| MC8640DTVU1000HC | MPU DUAL E600 1023-FCCBGA |
| MC8640DTHX1250HC | MPU DUAL E600 1023-FCCBGA |
| MC8640DTHX1067NC | MPU DUAL E600 1023-FCCBGA |
| MC8640DTHX1000NC | MPU DUAL E600 1023-FCCBGA |
| MC8640DTHX1000HC | MPU DUAL E600 1023-FCCBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC8640DTVU1067H | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series |
| MC8640DTVU1067N | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC8640DTVU1067NC | 功能描述:微处理器 - MPU G8,REV2.1,0.95V,-40 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MC8640DTVU1067NE | 功能描述:微处理器 - MPU G8 REV3.0 0.95V 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MC8640DTVU1250H | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series |
发布紧急采购，3分钟左右您将得到回复。