参数资料
型号: MCHC11F1VFNE3
厂商: Freescale Semiconductor
文件页数: 101/158页
文件大小: 0K
描述: MCU 8BIT 1KRAM 512EE 68-PLCC
标准包装: 18
系列: HC11
核心处理器: HC11
芯体尺寸: 8-位
速度: 3MHz
连通性: SCI,SPI
外围设备: POR,WDT
输入/输出数: 30
程序存储器类型: ROMless
EEPROM 大小: 512 x 8
RAM 容量: 1K x 8
电压 - 电源 (Vcc/Vdd): 4.75 V ~ 5.25 V
数据转换器: A/D 8x8b
振荡器型: 内部
工作温度: -40°C ~ 105°C
封装/外壳: 68-LCC(J 形引线)
包装: 管件
OPERATING MODES AND ON-CHIP MEMORY
TECHNICAL DATA
4-9
4.3.2 Initialization
Because bits in the following registers control the basic configuration of the MCU, an
accidental change of their values could cause serious system problems. The protec-
tion mechanism, overridden in special operating modes, requires a write to the protect-
ed bits only within the first 64 bus cycles after any reset, or only once after each reset.
Table 4-2 summarizes the write access limited registers.
4.3.2.1 CONFIG Register
CONFIG controls the presence and position of the EEPROM in the memory map.
CONFIG also enables the COP watchdog timer.
P indicates a previously programmed bit. P(L) indicates that the bit resets to the logic
level held in the latch prior to reset, but the function of COP is controlled by DISR bit
in TEST1 register.
The CONFIG register consists of an EEPROM byte and static latches that control the
start-up conguration of the MCU. The contents of the EEPROM byte are transferred
into static working latches during reset sequences. The operation of the MCU is con-
trolled directly by these latches and not by CONFIG itself. In normal modes, changes
to CONFIG do not affect operation of the MCU until after the next reset sequence.
When programming, the CONFIG register itself is accessed. When the CONFIG reg-
ister is read, the static latches are accessed.
These bits can be read at any time. The value read is the one latched into the register
from the EEPROM cells during the last reset sequence. A new value programmed into
this register cannot be read until after a subsequent reset sequence. Unused bits al-
ways read as ones.
In special test mode, the static latches can be written directly at any time. In all modes,
CONFIG bits can only be programmed using the EEPROM programming sequence,
and are neither readable nor active until latched via the next reset. Refer to 4.4.3 CON-
EE[3:0] — EEPROM Mapping Control
EE[3:0] select the upper four bits of the EEPROM base address. In single-chip and
bootstrap modes, EEPROM is forced to $FE00–$FFFF regardless of the value of
EE[3:0].
CONFIG — System Configuration Register
$103F
Bit 7
654321
Bit 0
EE3
EE2
EE1
EE0
NOCOP
EEON
RESET:
11111
P
11
Single Chip
11111
P(L)
1
Bootstrap
P
P1P1P
Expanded
PPPP
1
P(L)
1
0
Special Test
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料
PDF描述
SPC5515SAMLU66 MCU POWERPC 768K FLASH 176-LQFP
MCF5214CVM66 IC MPU 32BIT COLDF 256-MAPBGA
SPC5604PEF0MLQ6 IC MCU 32BIT 512KB FLASH 144LQFP
EGG.1B.308.CYM CONN RCPT 8POS PNL MNT SKT W/NUT
MC68HC16Z1CEH16 IC MCU 16BIT 16MHZ 132-PQFP
相关代理商/技术参数
参数描述
MCHC11KS1CFNE4 功能描述:8位微控制器 -MCU 68HC11KS4 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MCHC175AFR1 制造商:Rochester Electronics LLC 功能描述:- Bulk
MCHC40-330K-RC 制造商:ALLIED 制造商全称:Allied Components International 功能描述:Molded Chip Inductor High Current
MCHC705B16NCFNE 功能描述:IC MCU 8BIT 352 BYTES RAM 52PLCC RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 标准包装:1 系列:87C 核心处理器:MCS 51 芯体尺寸:8-位 速度:16MHz 连通性:SIO 外围设备:- 输入/输出数:32 程序存储器容量:8KB(8K x 8) 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4 V ~ 6 V 数据转换器:- 振荡器型:外部 工作温度:0°C ~ 70°C 封装/外壳:44-DIP 包装:管件 其它名称:864285
MCHC705B16NVFNE 功能描述:IC MCU 8BIT 15K OTP 52-PLCC RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 标准包装:1 系列:87C 核心处理器:MCS 51 芯体尺寸:8-位 速度:16MHz 连通性:SIO 外围设备:- 输入/输出数:32 程序存储器容量:8KB(8K x 8) 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4 V ~ 6 V 数据转换器:- 振荡器型:外部 工作温度:0°C ~ 70°C 封装/外壳:44-DIP 包装:管件 其它名称:864285