- 您现在的位置：买卖IC网 > PDF目录16523 > MCP1316T-29LE/OT (Microchip Technology)IC SUPERVISOR 2.90V P-P SOT23-5 PDF资料下载
参数资料
| 型号： | MCP1316T-29LE/OT |
| 厂商： | Microchip Technology |
| 文件页数： | 34/52页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR 2.90V P-P SOT23-5 |
| 标准包装： | 1 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 2.9V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 662 (CN2011-ZH PDF) |
| 其它名称： | MCP1316T-29LE/OTDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
MCP131X/2X
4.5 Watchdog Timer
The purpose of the Watchdog Timer (WDT) is to
increase system reliability. The Watchdog Timer
MCP131X/2X with a PIC ? microcontroller (MCU) and
the Watchdog input.
feature can be used to detect when the Host
Controller ’s program flow is not as expected. The
Watchdog Timer monitors for activity on the Watchdog
TABLE 4-3:
WATCHDOG TIMER
Input pin (WDI). The WDI pin is expected to be strobed
within a given time frame. When this time frame is
exceeded, without an edge transition on the WDI pin,
the Reset pin is driven active to reset the system. This
stops the Host Controller from continuing its erratic
behavior (“run-away” code execution).
The Watchdog Timer is external to the main portion of
the control system and monitors the operation of the
system. This feature is enabled by a falling edge on the
WDI pin (after device POR). Monitoring is then done by
requiring the embedded controller to force an edge
transition (falling or rising) on the WDI pin (“pet the
Watchdog”) within a predetermined time frame (T WD ).
If the MCP131X/2X does not detect an edge on the
WDI pin within the expected time frame, the
MCP131X/2X device will force the Reset pin active.
Min
4.3
71
1.12
17.9
↑
If the time between
WDI edges is less
than this, it
ensures that the
MCP131X/2X
never forces a
reset
t WDT
Typ
6.3
102
1.6
25.6
Max
9.3
153
2.4
38.4
↑
If the time
between WDI
edges is greater
than this, it
ensures that the
MCP131X/2X
always forces a
Units
ms
ms
sec
sec
The Watchdog Timer is in the disabled state when:
reset
?
?
?
?
The Device Powers up
A POR event occurred
A WDT event occurred
A Manual Reset (MR) event occurred
Note 1:
Shaded rows are custom ordered Watch-
dog Timer Periods (t WDT ) time outs. For
information on ordering devices with
these t WDT time outs, please contact your
local Microchip sales office. Minimum
When the Watchdog Timer is in the disabled state, the
WDI pin has an internal smart pull-up resistor enabled.
This pull-up resistor has a typical value of 52 k Ω . This
purchase volumes are required.
+5V
pull-up resistor holds the WDI signal in the high state,
until it is forced to another state.
MCP13XX
10 k Ω
After the embedded controller has initialized, if the
Watchdog Timer feature is to be used, then the embed-
ded controller can force the WDI pin low (V IL ). This also
enables the Watchdog Timer feature and disables the
3-Terminal
Regulator
(example:
MCP1700 )
+5V
0.1
μF
V CC
RST
WDI
MCLR
PIC ?
MCU
I/O
WDI pull-up resistor. Disabling the pull-up resistor
reduces the device’s current consumption. The pull-up
resistor will remain disconnected until the device has a
GND
power-on, a Reset event occurs, or after the WDT time
FIGURE 4-19:
Watchdog Timer.
out.
Once the Watchdog Timer has been enabled, the Host
Controller must force an edge transition (falling or ris-
ing) on the WDI pin before the minimum Watchdog
Timer time out to ensure that the Watchdog Timer does
not force the Reset pins (RST/RST) to the active state.
If an edge transition does not occur before the maxi-
mum time out occurs, then the MCP131X/2X will force
the Reset pins to their active state.
The MCP131X/2X supports four time outs. The stan-
dard offering devices have a typical Watchdog Timer
period (T WDT ) of 1.6 s. Table 4-3 shows the available
Watchdog Timer periods. The t WDT time out is a
function of the device voltage and temperature.
DS21985C-page 34
The software routine that strobes WDI is critical. The
code must be in a section of software that is executed
frequently enough so the time between edge
transitions is less than the Watchdog time out period.
One common technique controls the Host Controllers
I/O line from two sections of the program. The software
might set the I/O line high while operating in the
Foreground mode and set it low while in the
Background or Interrupt modes. If both modes do not
execute correctly, the Watchdog Timer issues reset
pulses.
? 2005-2012 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JVP-EZ-S | CONVERTER MOD DC/DC 13.8V 25W |
| UPM1K560MPD1TD | CAP ALUM 56UF 80V 20% RADIAL |
| GMM11DRTN-S13 | CONN EDGECARD 22POS .156 EXTEND |
| AQ1057N5J-T | INDUCTOR 7.5NH 400MA 0402 SMD |
| XR16V2651IM-0B-EB | EVAL BOARD FOR V2651 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1316T-29NE/OT | 功能描述:监控电路 ACTIVE LOW P-P WDI RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MCP1316T-46BE/OT | 功能描述:监控电路 ACTIVE LOW P-P WDI RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MCP1316T-46FE/OT | 功能描述:监控电路 ACTIVE LOW P-P WDI RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MCP1316T-46KE/OT | 制造商:Microchip Technology Inc 功能描述: |
| MCP1316T-46LE/OT | 功能描述:监控电路 Active low P-P RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。