- 您现在的位置：买卖IC网 > PDF目录1953 > MCP201T-I/SN (Microchip Technology)IC LIN TXRX ON-BOARD VREG 8SOIC PDF资料下载
参数资料
| 型号： | MCP201T-I/SN |
| 厂商： | Microchip Technology |
| 文件页数： | 23/40页 |
| 文件大小： | 0K |
| 描述： | IC LIN TXRX ON-BOARD VREG 8SOIC |
| 产品培训模块： | Microchip MCP20xx LIN Transceiver Overview |
| 标准包装： | 3,300 |
| 类型： | 线路收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | LIN |
| 电源电压： | 6 V ~ 18 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
2007 Microchip Technology Inc.
DS21730F-page 3
MCP201
1.0
DEVICE OVERVIEW
The MCP201 provides a physical interface between a
microcontroller and a LIN half-duplex bus. It is intended
for automotive and industrial applications with serial
bus speeds up to 20 Kbaud.
The MCP201 provides a half-duplex, bidirectional
communications interface between a microcontroller
and the serial network bus. This device will translate
the CMOS/TTL logic levels to LIN level logic, and vice
versa.
The LIN specification 1.3 requires that the transceiver
of all nodes in the system be connected via the LIN pin,
referenced to ground and with a maximum external
termination resistance of 510
Ω from LIN bus to battery
supply. The 510
Ω corresponds to 1 Master and 16
Slave nodes.
The MCP201 provides a +5V 50 mA regulated power
output. The regulator uses a LDO design, is short-
circuit-protected and will turn the regulator output off if
it falls below 3.5V. The MCP201 also includes thermal
shutdown protection. The regulator has been specifi-
cally designed to operate in the automotive environ-
ment and will survive reverse battery connections,
+40V load dump transients and double-battery jumps
1.1
Optional External Protection
1.1.1
TRANSIENT VOLTAGE
PROTECTION (LOAD DUMP)
An external 27V transient suppressor (TVS) diode,
between VBAT and ground, with a 50
Ω resistor in series
with the battery supply and the VBAT pin, serves to pro-
tect the device from power transients (see Figure 1-2)
and ESD events. While this protection is optional, it
should be considered as good engineering practice.
1.1.2
REVERSE BATTERY PROTECTION
An external reverse-battery-blocking diode can be
used to provide polarity protection (see Figure 1-2).
This protection is optional, but should be considered as
good engineering practice.
1.2
Internal Protection
1.2.1
ESD PROTECTION
For component-level ESD ratings, please refer to the
maximum operation specifications.
1.2.2
GROUND LOSS PROTECTION
The LIN bus specification states that the LIN pin must
transition to the recessive state when ground is
disconnected. Therefore, a loss of ground effectively
forces the LIN line to a hi-impedance level.
1.2.3
THERMAL PROTECTION
The thermal protection circuit monitors the die
temperature and is able to shut down the LIN
transmitter and voltage regulator. Refer to Table 1-1 for
details.
There are three causes for a thermal overload. A
thermal shut down can be triggered by any one, or a
combination
of,
the
following
thermal
overload
conditions.
Voltage regulator overload
LIN bus output overload
Increase in die temperature due to increase in
environment temperature
Driving the TXD and checking the RXD pin makes it
possible to determine whether there is a bus contention
(Rx = low, Tx = high) or a thermal overload condition
(Rx = high, Tx = low).
TABLE 1-1:
SOURCES OF THERMAL OVERLOAD(1,2)
Note:
After recovering from a thermal, bus or
voltage regulator overload condition, the
device will be in the Ready1 mode. In order
to go into Operational mode, the CS/
WAKE pin has to be toggled.
TXD
RXD
Comments
L
H
LIN transmitter shutdown, receiver and voltage regulator active, thermal overload
condition.
H
L
Regulator shutdown, receiver active, bus contention.
Legend: x = Don’t care, L = Low, H = High
Note 1:
LIN transceiver overload current on the LIN pin is 200 mA.
2:
Voltage regulator overload current on voltage regulator greater than 50 mA.
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2021A-330E/MD | IC TXRX LIN 3.3V LDO 8-DFN |
| MCP2022PT-500E/ST | IC TXRX LIN ON-BOARD VREG 14TSSO |
| MCP2022T-330E/ST | IC LIN TXRX ON-BD VREG 14TSSOP |
| MCP2036T-I/MG | INTEGRATED CIRCUITS LINEAR - 82 |
| MCP2036T-I/ML | IC AFE KEYLESS ENTRY 16QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2021 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator |
| MCP2021_12 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator |
| MCP2021-330E/MD | 功能描述:LIN 收发器 LIN ver 21 Trnsceivr w/ on-brd 33V Vreg RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MCP2021-330E/MF | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator |
| MCP2021-330E/P | 功能描述:LIN 收发器 LIN ver 21 Trnsceivr w/ on-brd 33V Vreg RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
发布紧急采购，3分钟左右您将得到回复。