- 您现在的位置：买卖IC网 > PDF目录10416 > MCP2050T-330E/SL (Microchip Technology)IC TXRX LIN 3.3V LDO 14-SOIC PDF资料下载
参数资料
| 型号： | MCP2050T-330E/SL |
| 厂商： | Microchip Technology |
| 文件页数： | 41/42页 |
| 文件大小： | 0K |
| 描述： | IC TXRX LIN 3.3V LDO 14-SOIC |
| 产品培训模块： | Microchip MCP20xx LIN Transceiver Overview |
| 标准包装： | 2,600 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页
2012 Microchip Technology Inc.
DS22299B-page 8
MCP2050
If CS/LWAKE = 0, the device can work in POWER-
DOWN mode or READY mode.
An internal pull-down resistor will keep the CS/LWAKE
pin low to ensure that no disruptive data will be present
on the bus while the microcontroller is executing a
Power-on Reset and I/O initialization sequence. When
CS/LWAKE is ‘1’, a weak pull-down (~600 k) is used
to reduce current. When CS/LWAKE is ‘0’ a stronger
pull-down (~300 k) is used to maintain the logic level.
This pin may also be used as a local wake-up input
(see Figure 1-14). The microcontroller will set the I/O
pin to control the CS/LWAKE. An external switch, or
other source, can then wake-up both the transceiver
and the microcontroller.
1.3.8
FAULT/TXE
Fault Detect Output/Transmitter Enable Input pin. The
output section is HV tolerant open drain (up to 30V).
The input section is identical with TXD section (TTL
level, HV compliant, adaptive pull-up). Internal
adaptive pull-up maintains this input high '1' if the pin is
floating. Its state is defined as shown in Table 1-3. The
device is placed in TRANSMITTER OFF mode
whenever this pin is LOW (‘0’), either from an internal
fault condition or by external drive.
If CS/LWAKE is HIGH (‘1”), the FAULT/TXE signals a
mismatch between the TXD input and the LBUS level.
This can be used to detect a bus contention. Since the
bus exhibits a propagation delay, the sampling of the
internal compare is debounced to eliminate false faults.
After the device wakes up, the FAULT/TXE indicates
what wakes the device if CS/LWAKE remains LOW (‘0’)
(refer to Table 1-3).
The FAULT/TXE pin sampled at a rate faster than every
10 s.
1.3.9
RESET
RESET OUTPUT pin. This pin is open drain with
~90 k pull-up to VREG. It indicates the internal
voltage has reached a valid, stable level. As long as the
internal voltage is valid (above 0.8VREG), this pin will
remain HIGH (‘1’); otherwise the RESET pin switches
to LOW (‘0’).
1.3.10
WWDTRESET
WWDTRESET is an open-drain output pin. This pin is
asserted low when the internal Windowed Watchdog
Timer has expired or an attempt was made to clear the
timer before the window has opened.
1.3.11
WWDTTRIG
This is an input pin to reset the Windowed Watchdog
Timer. A high-to-low transition during the open window
time will reset the timer and prevent the WWDT from
timing out. The pin has an internal adaptive pull-up to
an internally-generated 4.2V (approximate.).
When WWDTTRIG is ‘0’, a weak pull-up (~800 k
is
connected
to reduce current.
When WWDTTRIG is ‘1’ the pull-up is stronger to
maintain the logic level.
Note:
CS/LWAKE should NOT be tied directly to
pin VREG as this could force the
MCP2050 into Operation Mode before the
microcontroller is initialized.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B20-MX-F2 | CONVERTER MOD DC/DC 5V 75W |
| VI-J1F-MW-F1 | CONVERTER MOD DC/DC 72V 100W |
| VI-J1B-MW-F3 | CONVERTER MOD DC/DC 95V 100W |
| VI-J14-MW-F3 | CONVERTER MOD DC/DC 48V 100W |
| VI-J11-MW-F1 | CONVERTER MOD DC/DC 12V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2050T-500E/MQ | 功能描述:LIN 收发器 LIN Transceiver + 5.0V LDO + WWDT RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MCP2050T-500E/SL | 功能描述:LIN 收发器 LIN Transceiver + 5.0V LDO + WWDT RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MCP-20-I9-LL | 制造商:YAMAICHI 制造商全称:Yamaichi Electronics Co., Ltd. 功能描述:MatchCon |
| MCP-20-TI9-LL | 制造商:YAMAICHI 制造商全称:Yamaichi Electronics Co., Ltd. 功能描述:MatchCon |
| MCP-210-00005-01 | 制造商:Supermicro Computer Inc 功能描述:SPARE PARTS - Trays |
发布紧急采购，3分钟左右您将得到回复。