- 您现在的位置：买卖IC网 > PDF目录9442 > MCP40D19T-503E/LT (Microchip Technology)IC DGTL POT 50K 128TAPS SC70-5 PDF资料下载
参数资料
| 型号： | MCP40D19T-503E/LT |
| 厂商： | Microchip Technology |
| 文件页数： | 28/43页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 50K 128TAPS SC70-5 |
| 标准包装： | 1 |
| 接片： | 128 |
| 电阻（欧姆）： | 50k |
| 电路数： | 1 |
| 温度系数： | 标准值 150 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSSOP（5 引线），SC-88A，SOT-353 |
| 供应商设备封装： | SC-70-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 674 (CN2011-ZH PDF) |
| 其它名称： | MCP40D19T-503E/LTDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
MCP40D17/18/19
DS22152B-page 34
2009 Microchip Technology Inc.
5.2
I2C Bit Definitions
I2C bit definitions include:
Figure 5-8 shows the waveform for these states.
5.2.1
START BIT
The Start bit (see Figure 5-2) indicates the beginning of
a data transfer sequence. The Start bit is defined as the
SDA signal falling when the SCL signal is “High”.
FIGURE 5-2:
Start Bit.
5.2.2
DATA BIT
The SDA signal may change state while the SCL signal
is Low. While the SCL signal is High, the SDA signal
MUST be stable (see Figure 5-3).
FIGURE 5-3:
Data Bit.
5.2.3
ACKNOWLEDGE (A) BIT
The A bit (see Figure 5-4) is a response from the Slave
device to the Master device. Depending on the context
of the transfer sequence, the A bit may indicate
different things. Typically the Slave device will supply
an A response after the Start bit and 8 “data” bits have
been received. The A bit will have the SDA signal low.
FIGURE 5-4:
Acknowledge Waveform.
If the Slave Address is not valid, the Slave Device will
issue a Not A (A). The A bit will have the SDA signal
high.
If an error condition occurs (such as an A instead of A)
then a START bit must be issued to reset the command
state machine.
TABLE 5-1:
MCP40D17/18/19 A / A
RESPONSES
5.2.4
REPEATED START BIT
The Repeated Start bit (see Figure 5-5) indicates
the current
Master
Device
wishes
to
continue
communicating with the current Slave Device without
releasing the I2C bus. The Repeated Start condition is
the same as the Start condition, except that the
Repeated Start bit follows a Start bit (with the Data bits
+ A bit) and not a Stop bit.
The Start bit is the beginning of a data transfer
sequence and is defined as the SDA signal falling when
the SCL signal is “High”.
FIGURE 5-5:
Repeat Start Condition
Waveform.
SDA
SCL
S
1st Bit
2nd Bit
SDA
SCL
S
1st Bit
2nd Bit
A
8
D0
9
SDA
SCL
Event
Acknowledge
Bit Response
Comment
General Call
A
Slave Address
valid
A
Slave Address
not valid
A
Bus Collision
N.A.
I2C Module Resets,
or a “Don’t Care” if
the collision occurs
on the Masters
“Start bit”.
Note 1: A bus collision during the Repeated Start
condition occurs if:
SDA is sampled low when SCL goes
from low to high.
SCL goes low before SDA is
asserted low. This may indicate that
another master is attempting to
transmit a data "1".
SDA
SCL
Sr = Repeated Start
1st Bit
相关PDF资料 |
PDF描述 |
|---|---|
| MS27473P16A6P | CONN PLUG 6POS STRAIGHT W/PINS |
| MS27468P13A4S | CONN RCPT 4POS JAM NUT W/SCKT |
| MS27656T23A35PA | CONN RCPT 100POS WALL MNT W/PINS |
| MCP40D17T-502E/LT | IC DGTL POT 5K 128TAPS SC70-6 |
| MS27656E23A35PA | CONN RCPT 100POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP-410-00006-0N | 制造商:Supermicro Computer Inc 功能描述:SCREW BAG 100 PCS-LABEL FOR 2.5 IN TRAY - Bulk |
| MCP-410-00006-0N/SINGLE | 制造商:Supermicro Computer Inc 功能描述:SCREW, SINGLE MCP-410-00006-0N - Bulk |
| MCP-410-00007-0N | 制造商:Supermicro Computer Inc 功能描述:OPTIONAL BAG OF THE RAIL SCREWS - Bulk |
| MCP41010 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI⑩ Interface |
| MCP41010E/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI Interface |
发布紧急采购，3分钟左右您将得到回复。