- 您现在的位置：买卖IC网 > PDF目录9349 > MCP4141T-502E/SN (Microchip Technology)IC POT DGTL SNGL 5K SPI 8SOIC PDF资料下载
参数资料
| 型号： | MCP4141T-502E/SN |
| 厂商： | Microchip Technology |
| 文件页数： | 21/88页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL SNGL 5K SPI 8SOIC |
| 标准包装： | 3,300 |
| 系列： | WiperLock™ |
| 接片： | 129 |
| 电阻（欧姆）： | 5k |
| 电路数： | 1 |
| 温度系数： | 标准值 150 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 3 线 SPI（芯片选择） |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
MCP414X/416X/424X/426X
DS22059B-page 28
2008 Microchip Technology Inc.
3.1
Chip Select (CS)
The CS pin is the serial interface’s chip select input.
Forcing the CS pin to VIL enables the serial commands.
Forcing the CS pin to VIHH enables the high-voltage
serial commands.
3.2
Serial Data In (SDI)
The SDI pin is the serial interfaces Serial Data In pin.
This pin is connected to the Host Controllers SDO pin.
3.3
Serial Data In / Serial Data Out
(SDI/SDO)
On the MCP41X1 devices, pin-out limitations do not
allow for individual SDI and SDO pins. On these
devices, the SDI and SDO pins are multiplexed.
The MCP41X1 serial interface knows when the pin
needs to change from being an input (SDI) to being an
output (SDO). The Host Controller’s SDO pin must be
properly protected from a drive conflict.
3.4
Ground (VSS)
The VSS pin is the device ground reference.
3.5
Potentiometer Terminal B
The terminal B pin is connected to the internal potenti-
ometer’s terminal B.
The potentiometer’s terminal B is the fixed connection
to the Zero Scale wiper value of the digital potentiome-
ter. This corresponds to a wiper value of 0x00 for both
7-bit and 8-bit devices.
The terminal B pin does not have a polarity relative to
the terminal W or A pins. The terminal B pin can
support both positive and negative current. The voltage
on terminal B must be between VSS and VDD.
MCP42XX devices have two terminal B pins, one for
each resistor network.
3.6
Potentiometer Wiper (W) Terminal
The terminal W pin is connected to the internal potenti-
ometer’s terminal W (the wiper). The wiper terminal is
the adjustable terminal of the digital potentiometer. The
terminal W pin does not have a polarity relative to
terminals A or B pins. The terminal W pin can support
both positive and negative current. The voltage on
terminal W must be between VSS and VDD.
MCP42XX devices have two terminal W pins, one for
each resistor network.
3.7
Potentiometer Terminal A
The terminal A pin is available on the MCP4XX1
devices, and is connected to the internal potentiome-
ter’s terminal A.
The potentiometer’s terminal A is the fixed connection
to the Full Scale wiper value of the digital
potentiometer. This corresponds to a wiper value of
0x100 for 8-bit devices or 0x80 for 7-bit devices.
The terminal A pin does not have a polarity relative to
the terminal W or B pins. The terminal A pin can
support both positive and negative current. The voltage
on terminal A must be between VSS and VDD.
The terminal A pin is not available on the MCP4XX2
devices, and the internally terminal A signal is floating.
MCP42X1 devices have two terminal A pins, one for
each resistor network.
3.8
Write Protect (WP)
The WP pin is used to force the non-volatile memory to
be write protected.
3.9
Shutdown (SHDN)
The SHDN pin is used to force the resistor network
terminals into the hardware shutdown state.
3.10
Serial Data Out (SDO)
The SDO pin is the serial interfaces Serial Data Out pin.
This pin is connected to the Host Controllers SDI pin.
This pin allows the Host Controller to read the digital
potentiometers registers, or monitor the state of the
command error bit.
3.11
Positive Power Supply Input (VDD)
The VDD pin is the device’s positive power supply input.
The input power supply is relative to VSS.
While the device VDD < Vmin (2.7V), the electrical
performance of the device may not meet the data sheet
specifications.
3.12
No Connection (NC)
Those pins should be either connected to VDD or VSS.
3.13
Exposed Pad (EP)
This pad is conductively connected to the device's
substrate. This pad should be tied to the same potential
as the VSS pin (or left unconnected). This pad could be
used to assist as a heat sink for the device when
connected to a PCB heat sink.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27505E25B1P | CONN RCPT 128POS BOX MNT W/PINS |
| MCP4141T-502E/MS | IC POT DGTL SNGL 5K SPI 8MSOP |
| MS27466E25B1PA | CONN RCPT 128POS WALL MT W/PINS |
| MCP4141T-503E/MS | IC POT DGTL SNGL 50K SPI 8MSOP |
| MS27474E16F6P | CONN RCPT 6POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4141T-502I/MF | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory |
| MCP4141T-502I/ML | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory |
| MCP4141T-502I/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory |
| MCP4141T-502I/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory |
| MCP4141T-502I/SL | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory |
发布紧急采购，3分钟左右您将得到回复。