参数资料
型号: MCP4706A3T-E/CH
厂商: Microchip Technology
文件页数: 60/86页
文件大小: 0K
描述: IC DAC 8BIT NV EEP I2C SOT-23-6
标准包装: 3,000
设置时间: 6µs
位数: 8
数据接口: EEPROM,I²C,串行
转换器数目: 1
电压电源: 单电源
功率耗散(最大): 452mW
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: SOT-23-6
供应商设备封装: SOT-23-6
包装: 带卷 (TR)
输出数目和类型: 1 电压,单极
采样率(每秒): *
2011-2012 Microchip Technology Inc.
DS22272C-page 63
MCP4706/4716/4726
8.0
TYPICAL APPLICATIONS
The MCP47X6 family of devices are general purpose,
single channel voltage output DACs for various
applications
where
a
precision
operation
with
low-power and nonvolatile EEPROM memory is
needed.
Since the devices include a nonvolatile EEPROM
memory, the user can utilize these devices for
applications that require the output to return to the
previous set-up value on subsequent power-ups.
Applications generally suited for the devices are:
Set Point or Offset Trimming
Sensor Calibration
Portable Instrumentation (Battery Powered)
Motor Control
8.1
Connecting to I2C BUS using
Pull-Up Resistors
The SCL and SDA pins of the MCP47X6 devices are
open-drain configurations. These pins require a pull-up
resistor as shown in Figure 8-2.
The pull-up resistor values (R1 and R2) for SCL and
SDA pins depend on the operating speed (standard,
fast, and high speed) and loading capacitance of the
I2C bus line. A higher value of the pull-up resistor
consumes less power, but increases the signal
transition time (higher RC time constant) on the bus
line. Therefore, it can limit the bus operating speed.
The lower resistor value, on the other hand, consumes
higher power, but allows higher operating speed. If the
bus line has higher capacitance due to long metal
traces or multiple device connections to the bus line, a
smaller pull-up resistor is needed to compensate the
long RC time constant. The pull-up resistor is typically
chosen between 1 k
Ω and 10 kΩ ranges for Standard
and Fast modes, and less than 1 k
Ω for High-Speed
mode.
8.1.1
DEVICE CONNECTION TEST
The user can test the presence of the device on the I2C
bus line using a simple I2C command. This test can be
achieved by checking an acknowledge response from
the device after sending a Read or Write command.
Figure 8-1 shows an example with a Read command.
The steps are:
a)
Set the R/W bit “High” in the device’s address
byte.
b)
Check the ACK bit of the address byte.
If the device acknowledges (ACK = 0) the
command, then the device is connected,
otherwise it is not connected.
c)
Send Stop bit.
FIGURE 8-1:
I2C Bus Connection Test.
1
2
3
4
5
678
9
SCL
SDA
1
0
1
A2 A1 A0 1
Start
Bit
Address Byte
Address bits
Device Code
R/W
Stop
Bit
Device
AC
K
Response
相关PDF资料
PDF描述
VE-B3P-MY-F1 CONVERTER MOD DC/DC 13.8V 50W
MX7547KCWG+ IC DAC 12BIT DL MULT 24-SOIC
MCP4706A2T-E/MAY IC DAC 8BIT NV EEP I2C 6DFN
VE-B3N-MY-F3 CONVERTER MOD DC/DC 18.5V 50W
MCP4706A1T-E/MAY IC DAC 8BIT NV EEP I2C 6DFN
相关代理商/技术参数
参数描述
MCP471610M02041 制造商:Distributed By MCM 功能描述:Microsoft™ Xbox 360™ Replacement Black Game Controller 制造商:MCM 功能描述:MICROSOFT XBOX 360 CONTROLLER BLACK WIRED
MCP4716A0T-E/CH 功能描述:数模转换器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube
MCP4716A0T-E/MAY 功能描述:数模转换器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube
MCP4716A1T-E/CH 功能描述:数模转换器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube
MCP4716A1T-E/MAY 功能描述:数模转换器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube