- 您现在的位置：买卖IC网 > PDF目录17108 > MCP4728EV (Microchip Technology)BOARD EVAL 12BIT 4CH DAC MCP4728 PDF资料下载
参数资料
| 型号： | MCP4728EV |
| 厂商： | Microchip Technology |
| 文件页数： | 24/33页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL 12BIT 4CH DAC MCP4728 |
| 视频文件： | MCP4728 Evaluation Board Demo |
| 标准包装： | 1 |
| DAC 的数量： | 4 |
| 位数： | 12 |
| 数据接口： | I²C |
| 设置时间： | 6µs |
| DAC 型： | 电压 |
| 工作温度： | -40°C ~ 125°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | MCP4728 |
| 产品目录页面： | 673 (CN2011-ZH PDF) |
| 相关产品： | MCP4728T-E/UN-ND - IC DAC 12BIT W/I2C 10-MSOP MCP4728-E/UN-ND - IC DAC 12BIT W/I2C 10-MSOP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
MCP4728
DS22187E-page 30
2010 Microchip Technology Inc.
5.2.5
ACKNOWLEDGE
Each receiving device, when addressed, is obliged to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse, which is associated with this acknowledge bit.
The device that acknowledges has to pull down the
SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable LOW during the HIGH
period of the acknowledge related clock pulse. Of
course, setup and hold times must be taken into
account. During reads, a master must send an end of
data to the slave by not generating an acknowledge bit
on the last byte that has been clocked out of the slave.
In this case, the slave (MCP4728) will leave the data
line HIGH to enable the master to generate the STOP
condition.
FIGURE 5-1:
Data Transfer Sequence On The Serial Bus.
5.3
MCP4728 Device Addressing
The address byte is the first byte received following the
START condition from the master device. The first part
of the address byte consists of a 4-bit device code,
which is set to 1100 for the MCP4728 device. The
device code is followed by three I2C address bits (A2,
A1, A0) which are programmable by the users.
Although the three address bits are programmable at
the user’s application PCB, the user can also specify
the address bits during the product ordering process. If
there is no user’s request, the factory default setting of
the three address bits is “000”, programmed into the
EEPROM. The three address bits allow eight unique
addresses.
FIGURE 5-2:
Device Addressing.
5.3.1
PROGRAMMING OF I2C ADDRESS
BITS
When the customer first receives any new MCP4728
device, its default address bit setting is “000” if the
address bit programming was not requested. The
customer can reprogram the I2C address bits into the
EEPROM by using “Write Address Bit” command. This
write command needs current address bits. If the
address bits are unknown, the user can find them by
sending “General Call Read Address” Command. The
LDAC pin is also used to select the device of interest to
be programmed or to read the current address.
The following steps are needed for the I2C address
programming.
(a) Read the address bits using “General Call Read
Address” Command. (This is the case when the
address is unknown.)
(b) Write I2C address bits using “Write I2C Address
Bits” Command.
The Write Address command will replace the current
address with a new address in both input registers and
EEPROM.
See
for the details of reading the address bits, and
bits (C2=0, C1=1, C0=1)” for writing the address bits.
SCL
SDA
(A)
(B)
(D)
(A)
(C)
START
CONDITION
ADDRESS OR
ACKNOWLEDGE
VALID
DATA
ALLOWED
TO CHANGE
STOP
CONDITION
Start bit
Read/Write bit
Address Byte
R/W ACK
Acknowledge bit
Slave Address
110
0
Slave Address for MCP4728
A2
A1
A0
Device Code: Programmed (hard-wired) at the
factory.
Address Bits: Reprogrammable into EEPROM by
the user.
Device Code
Address Bits
相关PDF资料 |
PDF描述 |
|---|---|
| EMM08DRXI | CONN EDGECARD 16POS DIP .156 SLD |
| 9337110001 | HEAT SHRINK SLEEVE |
| 8420630001 | HEAT SHRINK SLEEVE |
| REF192GSZ-REEL | IC VREF SERIES PREC 2.5V 8-SOIC |
| SC43B-2R2 | INDUCTOR SMD 2.2UH 1.75A 7.96MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4728T-E/UN | 功能描述:数模转换器- DAC Quad 12-bit NV DAC with I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4729-E/SS | 功能描述:数模转换器- DAC Octal 12-bit NV DAC with I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP47A1T-A0E/LT | 功能描述:数模转换器- DAC 6-Bit Volatile DAC with Command Code RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP47A1T-A1E/LT | 功能描述:数模转换器- DAC 6-Bit Volatile DAC with Command Code RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP47DA1T-A0E/OT | 功能描述:数模转换器- DAC 6-bit windowed DAC voltage margining RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。