- 您现在的位置：买卖IC网 > PDF目录9442 > MCP47DA1T-A0E/OT (Microchip Technology)IC DGTL POT 30K 1CH SOT-23-6 PDF资料下载
参数资料
| 型号： | MCP47DA1T-A0E/OT |
| 厂商： | Microchip Technology |
| 文件页数： | 16/54页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 30K 1CH SOT-23-6 |
| 标准包装： | 1 |
| 接片： | 65 |
| 电阻（欧姆）： | 30k |
| 电路数： | 1 |
| 温度系数： | 标准值 150 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C |
| 电源电压： | 1.8 V ~ 5.5 V，2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 其它名称： | MCP47DA1T-A0E/OTDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
Micrel, Inc.
KSZ8041NL/RNL
September 2010
23
M9999-090910-1.4
MII Management (MIIM) Interface
The KSZ8041NL/RNL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface allows upper-layer devices to monitor and control the state of the
KSZ8041NL/RNL. An external device with MIIM capability is used to read the PHY status and/or configure the PHY
settings. Further details on the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows a external controller
to communicate with one or more PHY devices. Each KSZ8041NL/RNL device is assigned a unique PHY address
between 1 and 7 by its PHYAD[2:0] strapping pins. Also, every KSZ8041NL/RNL device supports the broadcast
PHY address 0, as defined per the IEEE 802.3 Specification, which can be used to read/write to a single
KSZ8041NL/RNL device, or write to multiple KSZ8041NL/RNL devices simultaneously.
A set of 16-bit MDIO registers. Register [0:6] are required, and their functions are defined per the IEEE 802.3
Specification. The additional registers are provided for expanded functionality.
The Table 1 shows the MII Management frame format for the KSZ8041NL/RNL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
00AAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
00AAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 1. MII Management Frame Format
Interrupt (INTRP)
INTRP (pin 21) is an optional interrupt signal that is used to inform the external controller that there has been a status
update to the KSZ8041NL/RNL PHY register. Bits[15:8] of register 1Bh are the interrupt control bits, and are used to
enable and disable the conditions for asserting the INTRP signal. Bits[7:0] of register 1Bh are the interrupt status bits, and
are used to indicate which interrupt conditions have occurred. The interrupt status bits are cleared after reading register
1Bh.
Bit 9 of register 1Fh sets the interrupt level to active high or active low.
MII Data Interface (KSZ8041NL only)
The Media Independent Interface (MII) is specified in Clause 22 of the IEEE 802.3 Specification. It provides a common
interface between physical layer and MAC layer devices, and has the following key characteristics:
Supports 10Mbps and 100Mbps data rates.
Uses a 25MHz reference clock, sourced by the PHY.
Provides independent 4-bit wide (nibble) transmit and receive data paths.
Contains two distinct groups of signals: one for transmission and the other for reception.
By default, the KSZ8041NL is configured to MII mode after it is power-up or reset with the following:
A 25MHz crystal connected to XI, XO (pins 9, 8), or an external 25MHz clock source (oscillator) connected to XI.
CONFIG[2:0] (pins 18, 29, 28) set to ‘000’ (default setting).
相关PDF资料 |
PDF描述 |
|---|---|
| MCP4531T-103E/MF | IC DGTL POT 10K 128TAPS 8-DFN |
| MCP40D19T-503E/LT | IC DGTL POT 50K 128TAPS SC70-5 |
| MS27473P16A6P | CONN PLUG 6POS STRAIGHT W/PINS |
| MS27468P13A4S | CONN RCPT 4POS JAM NUT W/SCKT |
| MS27656T23A35PA | CONN RCPT 100POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP47DA1T-A1E/OT | 功能描述:数模转换器- DAC 6-bit windowed DAC voltage margining RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4801-E/MC | 功能描述:数模转换器- DAC Sngl 8-bit DAC w/SPI interface intnl Vref RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4801-E/MS | 功能描述:数模转换器- DAC Sngl 8-bit DAC w/SPI interface intnl Vref RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4801-E/P | 功能描述:数模转换器- DAC Sngl 8-bit DAC w/SPI interface intnl Vref RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4801-E/SN | 功能描述:数模转换器- DAC Sngl 8-bit DAC w/SPI interface intnl Vref RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。