- 您现在的位置：买卖IC网 > PDF目录6206 > MCP6H01T-E/OT (Microchip Technology)IC OP AMP 16V 1.2MHZ SGL SOT23-5 PDF资料下载
参数资料
| 型号： | MCP6H01T-E/OT |
| 厂商： | Microchip Technology |
| 文件页数： | 10/46页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP 16V 1.2MHZ SGL SOT23-5 |
| 标准包装： | 3,000 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.8 V/µs |
| 增益带宽积： | 1.2MHz |
| 电流 - 输入偏压： | 10pA |
| 电压 - 输入偏移： | 700µV |
| 电流 - 电源： | 135µA |
| 电流 - 输出 / 通道： | 50mA |
| 电压 - 电源，单路/双路(±)： | 3.5 V ~ 16 V，±1.75 V ~ 8 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
| 其它名称： | MCP6H01T-E/OTTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
MCP6H01/2/4
DS22243D-page 18
2010-2011 Microchip Technology Inc.
For a unity gain buffer, VIN must be maintained below
VDD – 2.3V for correct operation.
4.2
Rail-to-Rail Output
The output voltage range of the MCP6H01/2/4 op amps
is 0.020V (typical) and 14.980V (typical) when
RL =10k is connected to VDD/2 and VDD =15V.
Refer
to
Figures 2-24
through
for
more
information.
4.3
Capacitive Loads
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases and the closed-loop bandwidth is
reduced. This produces gain peaking in the frequency
response, with overshoot and ringing in the step
response. While a unity-gain buffer (G = +1V/V) is the
most sensitive to capacitive loads, all gains show the
same general behavior.
When driving large capacitive loads with these op
amps (e.g., > 100 pF when G = + 1V/V), a small series
feedback loop’s phase margin (stability) by making the
output load resistive at higher frequencies. The
bandwidth will generally be lower than the bandwidth
with no capacitance load.
FIGURE 4-4:
Output Resistor, RISO
Stabilizes Large Capacitive Loads.
different capacitive loads and gains. The x-axis is the
normalized load capacitance (CL/GN), where GN is the
circuit’s noise gain. For non-inverting gains, GN and the
Signal Gain are equal. For inverting gains, GN is
1 + |Signal Gain| (e.g., -1V/V gives GN = +2V/V).
After selecting RISO for your circuit, double check the
resulting
frequency
response
peaking
and
step
response overshoot. Modify RISO’s value until the
response
is
reasonable.
Bench
evaluation
and
simulations with the MCP6H01/2/4 SPICE macro
model are helpful.
FIGURE 4-5:
Recommended RISO Values
for Capacitive Loads.
4.4
Supply Bypass
With this family of operational amplifiers, the power
supply pin (VDD for single supply) should have a local
bypass capacitor (i.e., 0.01 F to 0.1 F) within 2 mm
for good high-frequency performance. It can use a bulk
capacitor (i.e., 1 F or larger) within 100 mm to provide
large, slow currents. This bulk capacitor can be shared
with other analog parts.
4.5
Unused Op Amps
An unused op amp in a quad package (MCP6H04)
should be configured as shown in Figure 4-6. These
circuits prevent the output from toggling and causing
crosstalk. Circuit A sets the op amp at its minimum
noise gain. The resistor divider produces any desired
reference voltage within the output voltage range of the
op amp, and the op amp buffers that reference voltage.
Circuit B uses the minimum number of components
and operates as a comparator, but it may draw more
current.
FIGURE 4-6:
Unused Op Amps.
VIN
RISO
VOUT
CL
–
+
MCP6H0X
1
10
100
1000
1.E-11
1.E-10
1.E-09
1.E-08
1.E-07
1.E-06
Normalized Load Capacitance; CL/GN (F)
Re
c
o
m
en
d
ed
R
IS
O
(
)
GN:
1 V/V
2 V/V
5 V/V
VDD = 16V
RL = 10 k
10p
100p
1n
10n
0.1
1
1k
VDD
R1
R2
VDD
VREF
V
REF
V
DD
R
2
R
1
R
2
+
--------------------
=
MCP6H04 (A)
MCP6H04 (B)
相关PDF资料 |
PDF描述 |
|---|---|
| 0741621432 | CONN RCPT R/A 32POS 2.54MM GOLD |
| 5-1734531-0 | RCPT 2MM 50P R ANG MT 8AU 3.ST |
| MCP6H01T-E/MNY | IC OP AMP 16V 1.2MHZ SNGL 8TDFN |
| MCP6004-I/SL | IC OPAMP QUAD 1.8V 14SOIC |
| VAR-18080077M3P-XK | VARISTOR RING 7.7V 8.0MM 3-TERM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP6H02-E/SN | 功能描述:运算放大器 - 运放 1 MHz 16V Dual Gen Purpose Op amp SOIC RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MCP6H02-E/SN | 制造商:Microchip Technology Inc 功能描述:; Op Amp Type:Unity Gain Stable; No. of 制造商:Microchip Technology Inc 功能描述:IC, OP-AMP, 1.2MHz, 0.8V/ us, 3.5mV, SOIC-8 |
| MCP6H02T-E/MNY | 功能描述:运算放大器 - 运放 1 MHz 16V Dual Gen Purpose Op amp TDFN RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MCP6H02T-E/MNY | 制造商:Microchip Technology Inc 功能描述:; Op Amp Type:Unity Gain Stable; No. of 制造商:Microchip Technology Inc 功能描述:IC, OP-AMP, 1.2MHz, 0.8V/ us, 3.5mV, TDFN-8 |
| MCP6H02T-E/SN | 功能描述:运算放大器 - 运放 1 MHz 16V Dual Gen Purpose Op amp SOIC RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。