- 您现在的位置：买卖IC网 > PDF目录11655 > MCZ33784EF (Freescale Semiconductor)IC SENSOR DBUS DSI 2.02 16-SOIC PDF资料下载
参数资料
| 型号： | MCZ33784EF |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 10/30页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR DBUS DSI 2.02 16-SOIC |
| 标准包装： | 48 |
| 类型： | 传感器接口 |
| 输入类型： | 模拟 |
| 输出类型： | 数字 |
| 接口： | 总线 |
| 电流 - 电源： | 4mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Analog Integrated Circuit Device Data
18
Freescale Semiconductor
33784
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Normally enhanced long responses will be sent for
enhanced long commands, and enhanced short responses
will be sent for enhanced short commands of the same
length. If an enhanced long word is sent after an enhanced
short word, or an enhanced short word is sent after an
enhanced long word, or two enhanced short words of
different lengths are sent in succession, then the first
response will have a different length than the second
command, and therefore the first response will be invalid.
LOGIC COMMANDS AND REGISTERS
INTRODUCTION
The following sections describe in detail each of the
commands that can be sent to the 33784. All of these
commands can be sent in long-word format (standard or
enhanced). Some of the commands can be sent in short-
word format (standard or enhanced), but not all. Refer to the
table in each section for the available formats for each
command. The responses for each command can also be
found in the tables. The 4-bit CRC, which is appended to
every command and every response, has been omitted.
Many commands have “don't-care” bits, which can be set
to 0 or 1 without affecting the command. Although the 33784
will respond the same in either case, it is recommended that
all “don't-care” bits be set to 0 to maintain future compatibility.
INITIALIZATION COMMAND AND RESPONSE
(BUSIN INPUT ONLY)
Following power-up or after a POR has occurred, the
Initialization Command must be sent to the 33784 before it
will respond to other commands. The command format is
found in Figure 9.
The Initialization Command may be used to initialize a
daisy chain device. The Initialization Command is sent to
address zero. The command will be received by the next
daisy chain device with its bus switch open. Reception of this
command will assign the device address and close the bus
switch if the BSH and BSL bits are logic [1]
Once a device has received an Initialization Command, it
will ignore further initialization commands unless it has
received a clear command or undergone a power-ON reset.
The response is sent during the next message following a
valid Initialization Command to the addressed device. The
response is shown in Figure 9. Because this is a long-word
only command, there is no short word response. The BSH
and BSL bits returned are the same as the bits sent in the
command. The Request Status command can be used to find
the logic commanded state of the bus switches.
Figure 9. Initialization Command Response Format
REQUEST STATUS COMMAND AND RESPONSE
This command causes the addressed device to return the
status of the BSH and BSL bits and the logic levels of the I/
O. The command format is found in Figure 10.
The 33784 will only act on this command if the address bits
in the command match the address that the device was
initialized with. If the addresses do not match, the device will
do nothing and no response will be generated.
Data
Address
Command
Word Type
–
BSH BSL
OD
PA3 PA2 PA1 PA0
A3
A2
A1
A0
0
LW
Not Valid
SW & ESW (8-bit)
Not Valid
ESW (10-bit)
Response
Word Type
A3
A2
A1
A0
0
BSH BSL
0
PA3 PA2 PA1 PA0
LW
No Response
SW & ESW (8-bit)
No Response
ESW (10-bit)
Legend
A[3:0] = Address bits. The slave address.
An address value of 0000 is ignored by all devices (no
initialization, no bus switch closure, and no response)
BSH = High Side Bus Switch Position (1 = closed).
BSL = Low Side Bus Switch Position (1 = closed).
“–” = Don’t care bit. Can be 0 or 1.
PA[3:0] = Bus address to set the device to.
An address value of 0000 is ignored by all devices (no
initialization, no bus switch closure, and no response)
OD = Oscillator dither:
0 = no dither (default)
1 = dither
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JNR-IZ-B1 | CONVERTER MOD DC/DC 7.5V 25W |
| MCZ33793AEFR2 | IC DSI SLAVE SENSOR 16-SOIC |
| MCZ33793AEF | IC DSI SLAVE SENSOR 16-SOIC |
| VE-JNR-IY-F4 | CONVERTER MOD DC/DC 7.5V 50W |
| MC908JB16JDWE | IC MCU 16K FLASH 6MHZ USB 20SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33784EF/R2- | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:DSI 2.02 Sensor Interface |
| MCZ33784EFR2 | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33789AE | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33789AE/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Airbag System Basis Chip (SBC) with Power Supply and PSI5 Sensor Interface |
| MCZ33789AER2 | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。