- 您现在的位置：买卖IC网 > PDF目录11655 > MCZ33784EF (Freescale Semiconductor)IC SENSOR DBUS DSI 2.02 16-SOIC PDF资料下载
参数资料
| 型号： | MCZ33784EF |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 16/30页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR DBUS DSI 2.02 16-SOIC |
| 标准包装： | 48 |
| 类型： | 传感器接口 |
| 输入类型： | 模拟 |
| 输出类型： | 数字 |
| 接口： | 总线 |
| 电流 - 电源： | 4mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
33784
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
CLEAR COMMAND AND RESPONSE
This command will open the bus switch and reset all
registers to the reset state. The command format is found in
Figure 16. No response is generated for the clear command.
The 33784 will only act on this command if the address bits
in the command match the address that the device was
initialized with, or if the address bits are 0000.
Figure 16. Clear Command Format and Response Format
FORMAT CONTROL COMMAND AND RESPONSE
This command allows the short-word length, the CRC
polynomial, and the CRC seed to be changed. It is also the
command needed to switch the device from the “standard”
mode to the “enhanced” mode.
The response is sent during the next message following a
valid Format Control command to the addressed device.
Because this is a long-word only command, there is no short
word response.
On power-up or following a “Clear” command, the device
uses the standard DSI short-word length (8 data bits) and
standard CRC polynomial (x4 + 1) and seed (1010).
The registers associated with Format Control default to
values that correspond to Standard DBUS operation upon
power-up, or at the issuance of a “Clear” command.
Changes made to the Format Control Register do not
become active until the 4 bits of the format selection register
are set during a single write command. It will not switch back
to Standard DBUS settings unless all 4 bits of the format
selection register are cleared by a single write.
Any attempts to change the format will be ignored while in
the enhanced mode.
The Format Control command is a long-word Command
and contains 8 bits of data which are used to determine read
or write, the specific format control register, and the data to
be written/read. The format for this command is defined in
If the R/W bit is set, the value in the Data Bits will be written
to the format control register pointed to by the 3-bit format
register address. If the R/W bit is clear, the bits in the register
pointed to by the format register address will not be changed,
but the values in it will be returned in the following response
from the device. No data can be written to the reserved
registers.
The response to this command will be the data that was
written/read by the command. Attempts to write to the
reserved registers will return zeros in the data bits of the
response.
The 33784 will only act on the Format Control Command if
the address bits in the command match the address that the
device was initialized with. If the addresses do not match, the
device will do nothing and no response will be generated. The
only exception is the global address of 0000. If the address
bits in the command are 0000, the 33784 will perform all
normal functions associated with the command, but no
response will be generated.
Data
Address
Command
Word Type
––––––––
A3
A2
A1
A0
0111
LW & ELW
A3
A2
A1
A0
0111
SW & ESW (8-bit)
––
A3
A2
A1
A0
0111
ESW (10-bit)
Response
Word Type
No Response
LW & ELW
No Response
SW & ESW (8-bit)
No Response
ESW (10-bit)
Legend
A[3:0] = Address bits. The address of the selected device.
An address value of 0000 clears all devices.
“–” = Don’t care bit. Can be 0 or 1.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JNR-IZ-B1 | CONVERTER MOD DC/DC 7.5V 25W |
| MCZ33793AEFR2 | IC DSI SLAVE SENSOR 16-SOIC |
| MCZ33793AEF | IC DSI SLAVE SENSOR 16-SOIC |
| VE-JNR-IY-F4 | CONVERTER MOD DC/DC 7.5V 50W |
| MC908JB16JDWE | IC MCU 16K FLASH 6MHZ USB 20SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33784EF/R2- | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:DSI 2.02 Sensor Interface |
| MCZ33784EFR2 | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33789AE | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33789AE/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Airbag System Basis Chip (SBC) with Power Supply and PSI5 Sensor Interface |
| MCZ33789AER2 | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。