- 您现在的位置：买卖IC网 > PDF目录1954 > MCZ33784EFR2 (Freescale Semiconductor)IC SENSOR DBUS DSI 2.02 16-SOIC PDF资料下载
参数资料
| 型号： | MCZ33784EFR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 11/30页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR DBUS DSI 2.02 16-SOIC |
| 标准包装： | 2,500 |
| 类型： | 传感器接口 |
| 输入类型： | 模拟 |
| 输出类型： | 数字 |
| 接口： | 总线 |
| 电流 - 电源： | 4mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33784
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
The response is sent during the next message following a
valid Request Status command to the addressed device.
Because this is a long-word only command, there is no short-
word response.
The I/O bits reflect the logic states of the I/O pins. These
states are latched into an internal register after the Request
Status command is received (approximately TBD
μs after the
bus rises above the frame threshold), and are held until the
response is transmitted. Any activity that occurs on the I/O
pins after the states are latched will be ignored.
Figure 10. Request Status Command and Response Format
REQUEST AN0 COMMAND AND RESPONSE
This command causes the analog voltage on the AN0 pin
to be measured and converted by the on-chip 10-bit ADC.
The approximate timing for the conversion following this
command is shown in Figure 11. The response to this
command depends on the format in which the command was
sent. The sensor data is sent in the format shown in Table 10.
The 33784 will only act on this command if the address bits
in the command match the address that the device was
initialized with. If the addresses do not match, the device will
do nothing and no response will be generated.
Data
Address
Command
Word Type
––––––––
A3
A2
A1
A0
0001
LW & ELW
Not Valid
SW & ESW (8-bit)
Not Valid
ESW (10-bit)
Response
Word Type
A3
A2
A1
A0
00000
BSH BSL
00
IO2
IO1
IO0
LW & ELW
No Response
SW & ESW (8-bit)
No Response
ESW (10-bit)
Legend
A[3:0] = Address bits. The address of the selected device.
An address value of 0000 is ignored by all devices.
BSH = High Side Bus switch position (1 = closed).
BSL = Low Side Bus switch position (1 = closed).
“–” = Don’t care bit. Can be 0 or 1.
IO[2:0] = Values at logic I/Os.
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33793EF | IC DSI SLAVE REMOTE SENS 16-SOIC |
| MCZ33797EKR2 | IC SQUIB DRIVER 2CHAN 32-SOIC |
| MCZ33884EG | IC MULTIPLE CONTACT MON 24-SOIC |
| MCZ33905BD3EK | IC SBC CAN HS 3.3V 54SOIC |
| MCZ33972EWR2 | IC SWITCH DETECTION MULT 32-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33789AE | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33789AE/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Airbag System Basis Chip (SBC) with Power Supply and PSI5 Sensor Interface |
| MCZ33789AER2 | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33790EG | 功能描述:输入/输出控制器接口集成电路 DISTRIB SYS INTERFACE RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| MCZ33790EGR2 | 功能描述:输入/输出控制器接口集成电路 DISTRIB SYS INTERFACE RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。