- 您现在的位置：买卖IC网 > PDF目录16630 > MCZ33812EK (Freescale Semiconductor)IC DVR IGNITION/INJECTOR 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33812EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 13/25页 |
| 文件大小： | 0K |
| 描述： | IC DVR IGNITION/INJECTOR 32-SOIC |
| 标准包装： | 42 |
| 应用： | 自动 |
| 电流 - 电源： | 10mA |
| 电源电压： | 4.7 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 管件 |
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
are normally low and will go high when a fault is detected.
Toggling the respective input pin will clear the respective fault
pin if the fault has been cleared.
K-LINE COMMUNICATION (MTX, MRX, ISO9141)
These three pins are used to provide an ISO914, K-line
communication link for the MCU to provide diagnostic support
for the system. MRX is the +5.0 V logic level serial output line
to the MCU. MTX is the +5.0 V logic level serial input to the
IC from the MCU. The ISO9141 pin is a bidirectional line,
consistent with the ISO9141 specification for signalling to and
from the MCU.
RESET ( RESET )
The RESET pin is an open drain output.Without power on
the circuit, RESET is held low by an internal pull-down
resistor. When power is applied to the circuit and the voltage
on the VCC SENSE pin reaches the lower voltage threshold,
(5.0 volts - 2% = 4.9 V) the RESET pin will remain at a low
level (open drain FET turned on) for a period of time equal to
the value WD RESET . After this time period, the RESET pin will
then go high and stay high until a watchdog RESET is
generated, or an under-voltage event on VCC occurs. The
watchdog time and refresh features are controlled via the
WDRFSH line.
RELOAD AND REFRESH TIME (WDRFSH)
The WDRFSH pin is an input that is supplied by an MCU
output to set up the initial reload time, WD RELOAD , and to
refresh the watchdog timer. See the description of the
watchdog timer for information on how to use this pin.
WATCHDOG INHIBIT(WD_INH)
The WD_INH, watchdog inhibit pin, is normally tied to
ground. If desired, during software development, it can be
lifted from the ground pad and pulled high through an external
pull-up resistor. When high, WD_INH will prevent the
watchdog timer from causing a RESET because of a
watchdog timeout. The WD_INH should not be connected to
an MCU I/O pin or left floating in normal operation.
TEST PINS (TEST1, TEST2, AND TEST3)
These three pins are used only by Freescale test
engineering during the production testing of the 33812. They
are not to be used for any application purpose and must be
handled as specified in the pinout section of this document.
33812
Analog Integrated Circuit Device Data
Freescale Semiconductor
13
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B6W-EW | CONVERTER MOD DC/DC 5.5V 100W |
| 1-1625812-3 | INDUCTOR 470UH 500MA SMD |
| EEC26DRTI-S734 | CONN EDGECARD 52POS DIP .100 SLD |
| ECM24DCBN-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| Q2-F-5/8-01-QX15FT | HEATSHRINK POLY Q2F 5/8" BLK 15' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33812EK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Multifunctional Ignition and Injector Driver |
| MCZ33812EKR2 | 功能描述:马达/运动/点火控制器和驱动器 MULTIFUNC IGN, INJ DRVR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33879AEK | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SERIAL SW RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MCZ33879AEK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Configurable Octal Serial Switch with Open Load Detect Current Disable |
| MCZ33879AEKR2 | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SERIAL SW RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。