- 您现在的位置：买卖IC网 > PDF目录16630 > MCZ33812EK (Freescale Semiconductor)IC DVR IGNITION/INJECTOR 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33812EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 15/25页 |
| 文件大小： | 0K |
| 描述： | IC DVR IGNITION/INJECTOR 32-SOIC |
| 标准包装： | 42 |
| 应用： | 自动 |
| 电流 - 电源： | 10mA |
| 电源电压： | 4.7 V ~ 36 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 管件 |
FUNCTIONAL DEVICE OPERATION
IGNITION PRE-DRIVER OPERATION
INJOUT Fault Detection Features
Off State, Open Load Detection
An open load on the injector driver is detected by the
voltage level on the drain of the output device in the off state.
Internal to the device is a pull-down current source. In the
event of an open injector the drain voltage is pulled low.
When the voltage crosses the open load detection threshold,
an open load is detected. The open load fault detect
threshold is set internally and is not programmable. The open
load fault is reported as a high logic level on the INJFLT line.
On State, Shorted Load Detection
The INJOUT driver is capable of detecting a shorted
injector load (short to battery) in the on state. A shorted load
fault is reported when the drain pin voltage is greater than the
preset short threshold voltage. The shorted load fault detect
threshold is set internally and is not programmable. The
shorted load fault is reported as a high logic level on the
INJFLT line.
Clearing the INJFLT line
When the INJFLT line goes high for any of the following
reasons, while the INJIN line is high (on state):
? Short to battery
? Over-temperature
? Over-voltage
? Open load
The INJFLT line will remain high until the INJIN line goes
to a low logic level and the returns high (rising edge).
IGNITION PRE-DRIVER OPERATION
The Ignition pre-driver output is controlled by the logic
level input IGNIN. When IGNIN is high the IGNOUTH pin is
pulled high to IGNSUP. When the IGNIN pin is low, the
IGNOUTL line is pulled to ground turning off the driver
Darlington or IGBT.The IGNOUT pre-driver protects the
output device against over-current, short to battery, and
VPWR over-voltage.
IGNOUT OUTPUT PROTECTION FEATURES
Over-current and Short to battery (I LIM )
The Ignition Pre-driver protection scheme senses over-
current in the driver device by monitoring the voltage at the
IGNFB pin. Since this pin is protected by a 10:1 voltage
divider, the over-current threshold voltage is set internally to
1/10 of the voltage expected on the drain or collector of the
output device in an over-current situation. Since the Ignition
output device is external to the 33812, a short to battery is the
same as an over-current fault.
An over-current fault or short to battery is reported as a
high logic level on the IGNFLT line.
Temperature Limit (T LIM )
Since the Ignition output device is external to the 33812,
there is no over-temperature protection provided.
IGNOUT FAULT DETECTION FEATURES
output device in the off state (through a 10:1 voltage divider).
In the event of an open ignition coil the drain/collector voltage
is pulled low. When the voltage crosses the open load
detection threshold, an open load is detected. The open load
fault detect threshold is set internally and is not
programmable. An open load fault is reported as a high logic
level on the IGNFLT line.
Over-voltage (V PWR(OV) )
The Ignition pre-driver is also protected against an over-
voltage condition:
When the VPWR supply exceeds the V PWR(OV) threshold,
the IGNOUTL and IGNOUTH outputs turn off and stays off
until the over-voltage condition clears and the next rising
edge of the IGNIN input pin.
Clearing the IGNFLT line
When the IGNFLT line goes high for any of the following
reasons, while the IGNIN line is high (on state):
? Short to battery
? Over-voltage
? Over-temperature of the IGNOUTL and IGNOUTH
transistors
? Open load
The IGNFLT line will remain high until the IGNIN line goes
to the low logic level and then returns high.
Off State, Open Load Detection
An open load on the ignition driver external device is
detected by the voltage level on the drain or collector of the
33812
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B6W-EW | CONVERTER MOD DC/DC 5.5V 100W |
| 1-1625812-3 | INDUCTOR 470UH 500MA SMD |
| EEC26DRTI-S734 | CONN EDGECARD 52POS DIP .100 SLD |
| ECM24DCBN-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| Q2-F-5/8-01-QX15FT | HEATSHRINK POLY Q2F 5/8" BLK 15' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33812EK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Multifunctional Ignition and Injector Driver |
| MCZ33812EKR2 | 功能描述:马达/运动/点火控制器和驱动器 MULTIFUNC IGN, INJ DRVR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33879AEK | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SERIAL SW RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MCZ33879AEK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Configurable Octal Serial Switch with Open Load Detect Current Disable |
| MCZ33879AEKR2 | 功能描述:电源开关 IC - 配电 CONFIG OCTAL SERIAL SW RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。