- 您现在的位置：买卖IC网 > Datasheet目录342 > MCZ33937EKR2 (Freescale Semiconductor)IC PRE-DRIVER 3PHASE 54-SOIC Datasheet资料下载
参数资料
| 型号： | MCZ33937EKR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 40/48页 |
| 文件大小： | 0K |
| 描述： | IC PRE-DRIVER 3PHASE 54-SOIC |
| 标准包装： | 1,000 |
| 系列： | SMARTMOS™ |
| 配置： | 3 相桥 |
| 输入类型： | 非反相 |
| 延迟时间： | 265ns |
| 电流 - 峰： | 600mA |
| 配置数： | 1 |
| 输出数： | 3 |
| 高端电压 - 最大（自引导启动）： | 15V |
| 电源电压： | 8 V ~ 40 V |
| 工作温度： | -40°C ~ 135°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 54-SOICW-EP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页
FUNCTIONAL DEVICE OPERATION
INITIALIZATION REQUIREMENTS
IC INITIALIZATION
This process flow will initialize the IC and its software environment.
1. Apply power (V SYS ) to module
2. Remove RST (RST goes high, EN1 and EN2 are still low)
2.1. When RST rises above the threshold, the device will power-up. The charge pump (if configured) will start, allow V DD
and V LS to stabilize.
3. Initialize registers
3.1. Clear all interrupt status flags (send CINT0 and CINT1)
3.2. Initialize MASK register by sending 0010 xxxx or 0011 xxxx to mask out unwanted interrupts.
3.3. Set desired dead time either by commanding zero dead time or calibrating the dead time.
3.4. Send MODE command with desired bits, and also the Lock bit. e.g. 01000001. This prevents further mode changes.
4. Bring EN1 & EN2 high
5. Initialize the outputs
5.1. Command all Px_HS to logic 1 (High Side OFF)
5.2. Command all Px_LS to logic 1 (commanding Low Side ON). The input must transition from low to high after EN1 and
EN2 have gone high.
5.3. Wait for the bootstrap capacitors to charge (about 1us typically)
5.4. Command all Px_LS to logic 0 (command Low Side OFF)
5.5. Command all Px_HS to logic 0 (command High Side ON)
5.6. Command all Px_HS to logic 1 (command High Side OFF)
The device is now ready for normal operation.
INTERRUPT HANDLER
When an interrupt occurs, the general procedure is to send NULL0 and NULL1 commands to determine what happened, take
corrective action (if needed), clear the fault and return.
Because the return value from an SPI command is actually returned in the subsequent message, main-loop software that tries
to read SR1, SR2 or SR3, may experience an interrupt between sending the SPI command and the subsequent read. Thus if
these registers are to be read, special care must be taken in the software to ensure that the correct results are being interpreted.
33937A
Analog Integrated Circuit Device Data
40
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MDN2BL3GRAS | MOTOR BRUSHED DC 2V 2753RPM |
| MDN3BL3CSAS | MOTOR BRUSHED DC 2V 1458RPM |
| MIC2287-34YML TR | IC LED DRIVER WHITE BCKLGT 8-MLF |
| MIC2289C-34YD6 TR | IC LED DRIVR WHITE BCKLGT TSOT-6 |
| MIC2291YD5 TR | IC LED DRIVER PHOTO FLASH TSOT-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33970EG | 功能描述:马达/运动/点火控制器和驱动器 DUAL GAGE DRVR IMP DAMP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33970EG | 制造商:Freescale Semiconductor 功能描述:IC STEPPER MOTOR GAUGE DRIVER SPI |
| MCZ33970EGR2 | 功能描述:马达/运动/点火控制器和驱动器 DUAL GAGE DRVR IMP DAMP RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33972AEK | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MCZ33972AEK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Multiple Switch Detection Interface with Suppressed Wake-up |
发布紧急采购，3分钟左右您将得到回复。