- 您现在的位置：买卖IC网 > PDF目录1853 > MCZ34702EWR2 (Freescale Semiconductor)IC PWR SUPPLY 3A SW 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ34702EWR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 24/39页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY 3A SW 32-SOIC |
| 标准包装： | 1,000 |
| 应用： | 控制器，电源 QUICC? I、II |
| 输入电压： | 2.8 V ~ 6 V |
| 输出数： | 2 |
| 输出电压： | 7.75V，0.8 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 32-SOIC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Standard Power Sequencing Control
Comparators monitor voltage differences between the
LDO (LDO pin) and the switcher (VOUT pin) outputs as
follows:
1. LDO > VOUT + 1.9V, turn off LDO. The LDO can be
forced off. This occurs whenever the LDO output
voltage exceeds the switcher output voltage by more
than 1.9V.
2. LDO > VOUT + 2.0V, shunt LDO to ground. If turning
off the LDO is insufficient and the LDO output voltage
exceeds the switcher output voltage by more than
2.0V, a 1.5 ? shunt MOSFET is turned on that
discharges the LDO load capacitor to ground. The
shunt MOSFET is used for switcher output shorts to
ground and for power down in case of VIN1 ? VIN2
with the switcher output falling faster than the LDO.
3. LDO < VOUT + 1.9V cancel (2).
4. LDO < VOUT + 1.8V, cancel (1) above, re-enable LDO.
Normal operation resumes when the LDO output
voltage is less than 1.8V above the switcher output
voltage.
5. LDO < VOUT - 0.1V, turn off switcher. The switcher
can be forced off. This occurs whenever the LDO is
less than VOUT - 0.1V.
6. LDO < VOUT - 0.3V, turn on Sync (LS) MOSFET and
1.5 ? VOUT sink MOSFET. The buck high side
MOSFET is forced off and the Sync MOSFET is forced
on. This occurs when the switcher output voltage
exceeds the LDO output by more than 300mV.
7. LDO > VOUT - 0.3 V, cancel (6).
8. LDO > VOUT - 0.1V, cancel (5). Normal operation
resumes when LDO < VOUT - 0.1 V .
Inverted Power Sequencing Control
Comparators monitor voltage differences between the
switcher (VOUT pin) and LDO (LDO pin) outputs as follows:
1. VOUT > LDO + 1.8V, turn off VOUT . The switcher
VOUT can be forced off. This occurs whenever the
VOUT output voltage exceeds the LDO output voltage
by more than 1.8V.
2. VOUT > LDO + 2.0V, shunt VOUT to ground. If turning
off the switcher VOUT is insufficient and the VOUT
output voltage exceeds the LDO output voltage by
more than 2.0V, a 1.5 ? shunt MOSFET and the
switcher synchronous MOSFET are turned on to
discharge the VOUT load capacitor to ground. The
shunt MOSFET and synchronous MOSFET are used
for LDO output shorts to ground and for power-down in
case of VIN1 ? VIN2 with LDO output falling faster than
the VOUT .
3. VOUT < LDO + 1.8V, cancel (1) and (2) above, re-
enable VOUT . Normal operation resumes when the
VOUT output voltage is less than 1.8V above the LDO
output voltage.
4. VOUT < LDO + 2.0 V, cancel (2)
5. VOUT < LDO - 0.2V, turn off LDO. The LDO can be
forced off. This occurs whenever the VOUT is less than
VLDO - 0.2V.
6. VOUT < LDO - 0.3V, turn on the 1.5 ? LDO sink
MOSFET. This occurs when the LDO output voltage
exceeds the VOUT output by more than 300mV.
7. VOUT < LDO - 0.2 V, cancel (6).
8. VOUT < LDO - 0.1V, cancel (5). Normal operation
resumes when VOUT > LDO - 0.1 V .
STANDARD OPERATING MODE
Single 3.3V Supply, VIN = VIN1 = VIN2 = 3.3V
The 3.3V supplies the microprocessor I/O voltage, the
switcher supplies core voltage (e.g., 1.5V nominal), and the
LDO operates independently (see Figure 17 , page 22 ).
Power sequencing depends only on the normal switcher
intrinsic operation to control the buck high side MOSFET.
Power-up
When VIN is rising, initially VOUT is below the regulation
point and the buck high side MOSFET is on. In order not to
exceed the 2.1V differential requirement between the I/O
(VIN) and the core (VOUT), the switcher must start up at 2.1V
or less and be able to maintain the 2.1V or less differential.
The maximum slew rate for V IN is 1.0V/ms.
Power-down
When VIN is falling, VOUT falls below the regulation point;
therefore, the buck high side MOSFET is on. In the case
where VOUT is falling faster than VIN, the buck high side
MOSFET attempts to maintain VOUT. In the case where VIN
is falling faster than VOUT, the buck high side MOSFET is
also on, and the VOUT load capacitor is discharged through
the buck high side MOSFET to VIN. Thus, provided VIN does
not fall too fast, the core voltage (VOUT) does not exceed the
I/O voltage (VIN) by more than a maximum of 0.4V.
Shorted Load
1. VOUT shorted to ground. This causes the I/O voltage
to exceed the core voltage by more than 2.1V. No load
protection.
2. VIN shorted to ground. Until the switcher load
capacitance is discharged, the core voltage exceeds
the I/O voltage by more than 0.4V. By the intrinsic
operation of the switcher, the load capacitor is
discharged rapidly through the buck high side
MOSFET to VIN.
3. VOUT shorted to supply. No load protection. 34702 is
protected by current limit and thermal shutdown.
34702
Analog Integrated Circuit Device Data ?
24
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MDC3105DMT1 | IC INDUCTVE LOAD DRIVR 8V SC74-6 |
| MDP-02 | PLUG DBL BANANA W/WIRE GUIDE SET |
| MDP-S-9 | PLUG DBL BANANA W/SHORT BAR WHT |
| MDP-ST | PLUG DBL BANANA W/SOLDER TURRET |
| MDP-X | PLUG DBL BANANA ISOLAT W/4 TERM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ36304201 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36305001 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36444401 | 制造商:LG Corporation 功能描述:Duct |
| MCZ36620901 | 制造商:LG Corporation 功能描述:Duct |
| MCZ37250851 | 制造商:LG Corporation 功能描述:Duct |
发布紧急采购，3分钟左右您将得到回复。