参数资料
| 型号： | MIC2166YMME TR |
| 厂商： | Micrel Inc |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM HYBRID 10TSOP |
| 标准包装： | 2,500 |
| 系列： | Hyper Speed Control™ |
| PWM 型： | 混合物 |
| 输出数： | 1 |
| 频率 - 最大： | 750kHz |
| 占空比： | 82% |
| 电源电压： | 4.5 V ~ 28 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Micrel, Inc.
where:
R DS(ON) = on-resistance of the MOSFET switch
D = Duty Cycle = V OUT / V IN
Making the assumption that the turn-on and turn-off
transition times are equal; the transition times can be
MIC2166
where:
f SW = switching frequency
20% = ratio of AC ripple current to DC output current
V IN(max) = maximum power stage input voltage
The peak-to-peak inductor current ripple is:
t T =
Δ I L ( PP ) =
V OUT × ( V IN (max) ? V OUT )
approximated by:
C ISS × V DD + C OSS × V IN
I G
where:
C ISS and C OSS are measured at V DS = 0
(10)
(13)
V IN (max) × f SW × L
The peak inductor current is equal to the average output
current plus one half of the peak-to-peak inductor current
ripple.
I G = gate-drive current
The total high-side MOSFET switching loss is:
I L(PK) = I OUT(max) + 0.5 × Δ I L(PP)
(14)
P AC = (V IN + V D ) × I PK × t T × f SW
(11)
The RMS inductor current is used to calculate the I 2 R
losses in the inductor.
where:
t T = Switching transition time
V D = Diode drop
I L(RMS) = I OUT(max) 2 +
Δ I L(PP) 2
12
(15)
f SW = Switching Frequency
The high-side MOSFET switching losses increase with
the switching frequency and the input voltage V IN . The
low-side MOSFET switching losses are negligible and
can be ignored for these calculations.
Inductor Selection
Values for inductance, peak, and RMS currents are
required to select the output inductor. The input and
output voltages and the inductance value determine the
peak-to-peak inductor ripple current. Generally, higher
inductance values are used with higher input voltages.
Larger peak-to-peak ripple currents will increase the
power dissipation in the inductor and MOSFETs. Larger
output ripple currents will also require more output
capacitance to smooth out the larger ripple current.
Smaller peak-to-peak ripple currents require a larger
inductance value and therefore a larger and more
expensive inductor. A good compromise between size,
loss and cost is to set the inductor ripple current to be
Maximizing efficiency requires the proper selection of
core material and minimizing the winding resistance. The
high-frequency operation of the MIC2166 requires the
use of ferrite materials for all but the most cost sensitive
applications.
Lower cost iron powder cores may be used but the
increase in core loss will reduce the efficiency of the
power supply. This is especially noticeable at low output
power. The winding resistance decreases efficiency at
the higher output current levels. The winding resistance
must be minimized although this usually comes at the
expense of a larger inductor. The power dissipated in the
inductor is equal to the sum of the core and copper
losses. At higher output loads, the core losses are
usually insignificant and can be ignored. At lower output
currents, the core losses can be a significant contributor.
Core loss information is usually available from the
magnetics vendor. Copper loss in the inductor is
calculated by the equation below:
P INDUCTORCu =I L(RMS) × R WINDING
equal to 20% of the maximum output current. The
inductance value is calculated by equation 12:
2
(16)
L =
V OUT × ( V ΙΝ (max) ? V OUT )
V ΙΝ (max) × f SW × 20 % × I OUT (max)
(12)
September 2010
15
M9999-092410-C
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2168AYMM | IC REG CTRLR BUCK PWM VM 10-MSOP |
| MIC2168BMM TR | IC REG CTRLR BUCK PWM VM 10-MSOP |
| MIC2169AYMM | IC REG CTRLR DIVIDER PWM 10-MSOP |
| MIC2169BMM TR | IC REG CTRLR BUCK PWM VM 10-MSOP |
| MIC2169BYMME | IC REG CTRLR BUCK PWM VM 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2168 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1MHz PWM Synchronous Buck Control IC |
| MIC2168_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1MHz PWM Synchronous Buck Control IC |
| MIC2168A | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1MHz PWM Synchronous Buck Control IC |
| MIC2168ABMM | 功能描述:IC REG CTRLR BUCK PWM VM 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2168ABMM TR | 功能描述:IC REG CTRLR BUCK PWM VM 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。