- 您现在的位置：买卖IC网 > PDF目录15332 > MIC2183YQS TR (Micrel Inc)IC REG CTRLR BUCK PWM CM 16-QSOP PDF资料下载
参数资料
| 型号： | MIC2183YQS TR |
| 厂商： | Micrel Inc |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-QSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 440kHz |
| 占空比： | 100% |
| 电源电压： | 2.9 V ~ 14 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2183YQSTR MIC2183YQSTR-ND |
MIC2183
the oscillator frequency is reduced by approximately a factor
of 4. Frequency foldback is used to limit the energy delivered
to the output during a short circuit fault condition.
The SYNC input (pin 11) lets the MIC2183 synchronize with
an external clock signal. The rising edge of the sync signal
generates a reset signal in the oscillator, which turns off the
Micrel, Inc.
Lower values of R1 are preferred to prevent noise from
appearing on the FB pin. A typically recommended value is
10k ? . If R1 is too small in value it will decrease the efficiency
of the power supply, especially at low output loads.
Once R1 is selected, R2 can be calculated with the following
formula.
low side gate drive output. The high side drive then turns on,
restarting the switching cycle. The sync signal is inhibited
when the controller operates in frequency foldback. The sync
R 2 =
V REF × R 1
V OUT ± V REF
signal frequency must be greater than the maximum speci-
fied free running frequency of the MIC2183. If the synchroniz-
ing frequency is lower, double pulsing of the gate drive
outputs will occur. When not used, the sync pin must be
connected to ground.
The maximum recommended output switching frequency is
600kHz. Synchronizing to higher frequencies may be pos-
sible, however, higher power dissipation in the internal gate
drive circuits will occur. The MOSFET gates require charge
to turn on the device. The average current required by the
MOSFET gate increases with switching frequency.
Soft Start
Soft start reduces the power supply input surge current at
start up by controlling the output voltage risetime. The input
surge appears while the output capacitance is charged up. A
slower output risetime will draw a lower input surge current.
Soft start may also be used for power supply sequencing.
The soft start voltage is applied directly to the PWM compara-
tor. A 5 μ A internal current source is used to charge up the soft
start capacitor. The capacitor is discharged when either the
enable pin voltage drops below the standby threshold or the
V DD voltage drops below its UVLO level.
The part switches at a low duty cycle when the soft start pin
voltage is zero. As the soft start voltage rises from 0V to 0.7V,
the duty cycle increases from the minimum duty cycle to the
operating duty cycle. The oscillator runs at the foldback
frequency (1/4 of the switching frequency) until the feedback
voltage rises above 0.3V. The risetime of the output is
dependent of the soft start capacitor output capacitance,
input and output voltage and load current.
Voltage Setting Components
The MIC2183 requires two resistors to set the output voltage
as shown in Figure 5.
MIC2183 V OUT
Efficiency Considerations
Efficiency is the ratio of output power to input power. The
difference is dissipated as heat in the buck converter. Under
light output load, the significant contributors are:
? The V IN A supply current
? The V IN P supply current, which includes the current
required to switch the external MOSFETs
? Core losses in the output inductor
To maximize efficiency at light loads:
? Use a low gate charge MOSFET or use the smallest
MOSFET, which is still adequate for maximum output
current.
? Use a ferrite material for the inductor core, which has
less core loss than an MPP or iron power core.
Under heavy output loads the significant contributors to
power loss are (in approximate order of magnitude):
? Resistive on time losses in the MOSFETs
? Switching transition losses in the high side MOSFET
? Inductor resistive losses
? Current sense resistor losses
? Input capacitor resistive losses (due to the capacitors
ESR)
To minimize power loss under heavy loads:
? Use low on resistance MOSFETs. Use low threshold
logic level MOSFETs when the input voltage is below
5V. Multiplying the gate charge by the on resistance
gives a figure of merit, providing a good balance
between low load and high load efficiency.
? Slow transition times and oscillations on the voltage
and current waveforms dissipate more power during
the turn on and turn off of the MOSFETs. A clean
layout will minimize parasitic inductance and capaci
tance in the gate drive and high current paths. This
will allow the fastest transition times and waveforms
without oscillations. Low gate charge MOSFETs will
Voltage
Amplifier
Pin 6
R1
R2
transition faster than those with higher gate charge
requirements.
? For the same size inductor, a lower value will have
fewer turns and therefore, lower winding resistance.
However, using too small of a value will require more
output capacitors to filter the output ripple, which will
V REF
1.245V
Figure 5
The output voltage is determined by the equation below.
force a smaller bandwidth, slower transient response
and possible instability under certain conditions.
? Lowering the current sense resistor value will de
crease the power dissipated in the resistor. However,
it will also increase the overcurrent limit and will
V OUT = V REF × 1 +
R1
R 2
require larger MOSFETs and inductor components.
? Use low ESR input capacitors to minimize the power
Where: V REF for the MIC2183 is typically 1.245V.
dissipated in the capacitors ESR.
April 2005
11
M9999-042205
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2186YM TR | IC REG CTRLR BST FLYBK CM 16SOIC |
| ASM10DRYH-S13 | CONN EDGECARD 20POS .156 EXTEND |
| UPM1E152MHD | CAP ALUM 1500UF 25V 20% RADIAL |
| MIC2185YM TR | IC REG CTRLR BST PWM CM 16-SOIC |
| IDCS2512ER152M | INDUCTOR POWER 1500UH 0.12A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2184 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Voltage Buck PWM Control IC Final Information |
| MIC2184_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Voltage Buck PWM Control IC |
| MIC2184BM | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2184BM TR | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2184BQS | 功能描述:IC REG CTRLR BUCK PWM CM 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。