- 您现在的位置：买卖IC网 > PDF目录15332 > MIC2183YQS TR (Micrel Inc)IC REG CTRLR BUCK PWM CM 16-QSOP PDF资料下载
参数资料
| 型号： | MIC2183YQS TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-QSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 440kHz |
| 占空比： | 100% |
| 电源电压： | 2.9 V ~ 14 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2183YQSTR MIC2183YQSTR-ND |
MIC2183
The MIC2183 controller is broken down into 7 functions.
? Control loop
? PWM operation
? Current mode control
? Current limit
? Reference, enable and UVLO
? FreqOut
? MOSFET gate drive
? Oscillator and Sync
? Soft-start
Control Loop
Micrel, Inc.
Current Limit
The output current is detected by the voltage drop across the
external current sense resistor (R SENSE in Figure 1.). The
current sense resistor must be sized using the minimum
current limit threshold. The external components must be
designed to withstand the maximum current limit. The current
sense resistor value is calculated by the equation below:
MIN _ CURRENT _ SENSE _ THRESHOLD
R SENSE =
I OUT _ MAX
The maximum output current is:
PWM Control Loop
The MIC2183 uses current mode control to regulate the
I OUT _ MAX =
MAX _ CURRENT _ SENSE _ THRESHOLD
R SENSE
output voltage. This dual control loop method (illustrated in
Figure 2) senses the output voltage (outer loop) and the
inductor current (inner loop). It uses inductor current and
output voltage to determine the duty cycle of the buck
converter. Sampling the inductor current effectively removes
the inductor from the control loop, which simplifies compen-
sation.
V IN
The current sense pins CSH (pin 9) and CSL (pin 8) are noise
sensitive due to the low signal level and high input imped-
ance. The PCB traces should be short and routed close to
each other. A small (1nF) capacitor across the pins will
attenuate high frequency switching noise.
When the peak inductor current exceeds the current limit
threshold, the overcurrent comparator turns off the high side
MOSFET for the remainder of the switching cycle, effectively
Switching
Converter
Switch
I INDUCTOR
V OUT
Voltage
Divider
decreasing the duty cycle. The output voltage drops as
additional load current is pulled from the converter. When the
voltage at the feedback pin (FB) reaches approximately 0.3V,
the circuit enters frequency foldback mode and the oscillator
frequency will drop to 1/4 of the switching frequency. This
limits the maximum output power delivered to the load under
a short circuit condition.
Driver
V ERROR
V REF
Reference, Enable and UVLO Circuits
The output drivers are enabled when the following conditions
I INDUCTOR
V ERROR
t ON
t PER
D = t ON /t PER
Figure 2. Current Mode Control Example
As shown in Figure 1, the inductor current is sensed by
measuring the voltage across the resistor, R SENSE . A ramp is
added to the amplified current sense signal to provide slope
compensation, which is required to prevent unstable opera-
tion at duty cycles greater than 50%.
A transconductance amplifier is used for the error amplifier,
which compares an attenuated sample of the output voltage
with a reference voltage. The output of the error amplifier is
the compensation pin (Comp), which is compared to the
current sense waveform in the PWM block. When the current
signal becomes greater than the error signal, the comparator
turns off the high side drive. The COMP pin provides access
to the output of the error amplifier and allows the use of
external components to stabilize the voltage loop.
are satisfied:
? The V DD voltage (pin 10) is greater than its
undervoltage threshold.
? The voltage on the enable pin (pin 7) is greater
than the enable UVLO threshold.
The enable pin (pin 7) has two threshold levels, allowing the
MIC2183 to shut down in a low current mode, or turn off output
switching in standby mode. An enable pin voltage lower than
the shutdown threshold turns off all the internal circuitry and
places the MIC2183 in a micropower shutdown mode.
If the enable pin voltage is between the shutdown and
standby thresholds, the internal bias, V DD and reference
voltages are turned on. The soft start pin is forced low by an
internal discharge MOSFET. The output drivers are inhibited
from switching. The OUTP pin is in a high state and the OUTN
pin remains in a low state. Raising the enable voltage above
the standby threshold allows the soft start capacitor to charge
and enables the output drivers. The standby threshold is
specified in the electrical characteristics. A resistor divider
can be used with the enable pin to prevent the power supply
from turning on until a specified input voltage is reached. The
circuit in Figure 3 shows how to connect the resistors.
April 2005
9
M9999-042205
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2186YM TR | IC REG CTRLR BST FLYBK CM 16SOIC |
| ASM10DRYH-S13 | CONN EDGECARD 20POS .156 EXTEND |
| UPM1E152MHD | CAP ALUM 1500UF 25V 20% RADIAL |
| MIC2185YM TR | IC REG CTRLR BST PWM CM 16-SOIC |
| IDCS2512ER152M | INDUCTOR POWER 1500UH 0.12A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2184 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Voltage Buck PWM Control IC Final Information |
| MIC2184_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Voltage Buck PWM Control IC |
| MIC2184BM | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2184BM TR | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2184BQS | 功能描述:IC REG CTRLR BUCK PWM CM 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。