- 您现在的位置：买卖IC网 > PDF目录14847 > MIC4724YMME (Micrel Inc)IC REG BUCK ADJ 3A 10MSOP PDF资料下载
参数资料
| 型号： | MIC4724YMME |
| 厂商： | Micrel Inc |
| 文件页数： | 12/19页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3A 10MSOP |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 1V |
| 输入电压： | 3 V ~ 6 V |
| 频率 - 开关： | 2MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 产品目录页面： | 1093 (CN2011-ZH PDF) |
| 其它名称： | 576-3120-5 |
V OUT = V FB ?
+ 1 ?
C FF =
Micrel, Inc.
Component Selection
Input Capacitor
A 10μF ceramic is recommended on each VIN pin for
bypassing. X5R or X7R dielectrics are recommended for
the input capacitor. Y5V dielectrics lose most of their
capacitance over temperature and are therefore, not
recommended. Also, tantalum and electrolytic capacitors
alone are not recommended due their reduced RMS
current handling, reliability, and ESR increases.
An additional 0.1μF is recommended close to the VIN
and PGND pins for high frequency filtering. Smaller case
size capacitors are recommended due to their lower
ESR and ESL. Please refer to layout recommendations
for proper layout of the input capacitor.
Output Capacitor
The MIC4724 is designed for a 4.7μF output capacitor.
X5R or X7R dielectrics are recommended for the output
capacitor. Y5V dielectrics lose most of their capacitance
over temperature and are therefore not recommended.
In addition to a 4.7μF, a small 0.1μF is recommended
close to the load for high frequency filtering. Smaller
case size capacitors are recommended due to there
lower equivalent series ESR and ESL.
The MIC4724 utilizes type III voltage mode internal
compensation and utilizes an internal zero to
compensate for the double pole roll off of the LC filter.
For this reason, larger output capacitors can create
instabilities. In cases where a 4.7μF output capacitor is
not sufficient, other values of capacitance can be used
but the original LC filter pole frequency determined by
CO = 4.7μF + L = 1μH (which is approximately 73.4KHz)
must remain fixed. Increasing COUT forces L to
decrease and vice versa.
Inductor Selection
The MIC4724 is designed for use with a 1μH inductor.
Proper selection should ensure the inductor can handle
the maximum average and peak currents required by the
load. Maximum current ratings of the inductor are
generally given in two methods; permissible DC current
and saturation current. Permissible DC current can be
rated either for a 40°C temperature rise or a 10% to 20%
loss in inductance. Ensure the inductor selected can
handle the maximum operating current. When saturation
current is specified, make sure that there is enough
margin that the peak current will not saturate the
inductor.
MIC4724
Diode Selection
Since the MIC4724 is non-synchronous, a free-wheeling
diode is required for proper operation. A Schottky diode
is recommended due to the low forward voltage drop
and their fast reverse recovery time. The diode should
be rated to be able to handle the average output current.
Also, the reverse voltage rating of the diode should
exceed the maximum input voltage. The lower the
forward voltage drop of the diode the better the
efficiency. Please refer to the layout recommendations to
minimize switching noise.
Feedback Resistors
The feedback resistor set the output voltage by dividing
down the output and sending it to the feedback pin. The
feedback voltage is 1.0V. Calculating the set output
voltage is as follows;
? R1 ?
? R2 ?
Where R1 is the resistor from VOUT to FB and R2 is the
resistor from FB to GND. The recommended feedback
resistor values for common output voltages are available
in the bill of materials on page 19. Although the range of
resistance for the FB resistors is very wide, R1 is
recommended to be 10K. This minimizes the effect the
parasitic capacitance of the FB node.
Feedforward Capacitor (C FF )
A capacitor across the resistor from the output to the
feedback pin (R1) is recommended for most designs.
This capacitor can give a boost to phase margin and
increase the bandwidth for transient response. Also,
large values of feedforward capacitance can slow down
the turn-on characteristics, reducing inrush current. For
maximum phase boost, C FF can be calculated as follows;
1
2 π × 200kHz × R1
Bias filter
A small 10 ? resistor is recommended from the input
supply to the bias pin along with a small 0.1μF ceramic
capacitor from bias to ground. This will bypass the high
frequency noise generated by the violent switching of
high currents from reaching the internal reference and
control circuitry. Tantalum and electrolytic capacitors are
not recommended for the bias, these types of capacitors
lose their ability to filter at high frequencies.
June 2008
12
M9999-062408-A
相关PDF资料 |
PDF描述 |
|---|---|
| MIC4684YM | IC REG BUCK ADJ 2A 8SOIC |
| LGU2F221MELA | CAP ALUM 220UF 315V 20% SNAP |
| LM2575-12YN | IC REG BUCK 12V 1A 16DIP |
| LM2576-12WU | IC REG BUCK 12V 3A TO263-5 |
| PM2110-6R8M | INDUCTOR TOROID 6.8UH 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC4724YMME TR | 功能描述:直流/直流开关调节器 3A 2MHz Buck Regulator in Epad MSOP-10 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC47300 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3A, Low Voltage, Adjustable LDO Regulator with Dual Input Supply |
| MIC47300WD | 制造商:Micrel 功能描述:Micrel MIC47300WD, Low-Dropout (LDO) Voltage Regulators |
| MIC47300WD TR | 功能描述:低压差稳压器 - LDO 3A Low Voltage, ADJ. High Bandwidth LDO Regulator with Dual Input Supplies RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC47300WD-TR | 功能描述:Linear Voltage Regulator IC Positive Adjustable 1 Output Adj to 0.9V 3A TO-252-5 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 稳压器拓扑:正，可调式 电压 - 输出:可调至 0.9V 电流 - 输出:3A 电压 - 跌落（典型值）:0.23V @ 3A 稳压器数:1 电压 - 输入:1.4 V ~ 6.5 V 电流 - 限制（最小值）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-252-6，DPak（5 引线 + 接片） 供应商器件封装:TO-252-5 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。