- 您现在的位置：买卖IC网 > PDF目录14835 > MIC4744YTSE (Micrel Inc)IC REG BUCK ADJ 2A DL 16TSSOP PDF资料下载
参数资料
| 型号： | MIC4744YTSE |
| 厂商： | Micrel Inc |
| 文件页数： | 13/23页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 2A DL 16TSSOP |
| 标准包装： | 94 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 可调至 0.6V |
| 输入电压： | 2.9 V ~ 5.5 V |
| 频率 - 开关： | 4MHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-EPAD TSSOP |
| 产品目录页面： | 1093 (CN2011-ZH PDF) |
| 其它名称： | 576-3357-5 |
Micrel, Inc.
Component Selection
Input Capacitor
A 10μF ceramic is recommended on each VIN pin for
bypassing. X5R or X7R dielectrics are recommended for
the input capacitor. Y5V dielectrics lose most of their
capacitance over temperature and are therefore, not
recommended. Also, tantalum and electrolytic capacitors
alone are not recommended due to their reduced RMS
current handling, reliability, and ESR increases.
An additional 0.1μF is recommended close to the VIN and
PGND pins for high frequency filtering. Smaller case size
capacitors are recommended due to their lower ESR and
ESL. Please refer to layout recommendation for proper
layout of the input capacitor.
Output Capacitor
The MIC4744 is designed for a 4.7μF output capacitor and
MIC4744
Diode Selection
Since the MIC4744 is non-synchronous, a free-wheeling
diode is required for proper operation. A Schottky diode is
recommended due to the low forward voltage drop and
their fast reverse recovery time. The diode should be rated
to be able to handle the average output current. Also, the
reverse voltage rating of the diode should exceed the
maximum input voltage. The lower the forward voltage drop
of the diode the better the efficiency. Please refer to the
layout recommendation to minimize switching noise.
Feedback Resistors
The feedback resistor set the output voltage by dividing
down the output and sending it to the feedback pin. The
feedback voltage is 0.6V. Calculating the set output voltage
is as follows:
V OUT = V FB ?
+ 1 ?
a 1μH inductor or a 10μF output capacitor and a 0.47μH
inductor. X5R or X7R dielectrics are recommended for the
output capacitor. Y5V dielectrics lose most of their
? R1
? R2
?
?
capacitance over temperature and are therefore not
recommended.
In addition to a 4.7μF or a 10μF, a small 0.1μF is
recommended close to the load for high frequency filtering.
Smaller case size capacitors are recommended due to
there lower equivalent series ESR and ESL.
The MIC4744 utilizes type III voltage mode internal
compensation and utilizes an internal zero to compensate
for the double pole roll off of the LC filter. For this reason,
larger output capacitors can create instabilities. In cases
where a 4.7μF output capacitor or a 10μF output capacitor
is not sufficient, other values of capacitance can be used
but the original LC filter pole frequency determined by C OUT
= 10μF and L = 0.47μH (which is approximately 73.4KHz)
must remain fixed. Increasing C OUT forces L to decrease
and vice versa.
Where R1 is the resistor from V OUT to FB and R2 is the
resistor from FB to GND. The recommended feedback
resistor values for common output voltages are available in
the bill of materials on page 17. Although the range of
resistance for the FB resistors is very wide, R1 is
recommended to be 10K. This minimizes the effect the
parasitic capacitance of the FB node.
Feedforward Capacitor (C FF )
A capacitor across the resistor from the output to the
feedback pin (R1) is recommended for most designs. This
capacitor can give a boost to phase margin and increase
the bandwidth for transient response. Also, large values of
feedforward capacitance can slow down the turn-on
characteristics, reducing inrush current. For maximum
phase boost, C FF can be calculated as follows:
Inductor Selection
The MIC4744 is designed for use with a 0.47μH inductor
C FF =
1
2 π × 200kHz × R1
and a 10μF output capacitor or a 1μH inductor and a 4.7μF
output capacitor. Proper selection should ensure the
inductor can handle the maximum average and peak
currents required by the load. Maximum current ratings of
the inductor are generally given in two methods;
permissible DC current and saturation current. Permissible
DC current can be rated either for a 40°C temperature rise
or a 10% to 20% loss in inductance. Ensure the inductor
selected can handle the maximum operating current. When
saturation current is specified, make sure that there is
enough margin that the peak current will not saturate the
inductor.
Large values of feedforward capacitance may introduce
negative FB pin voltage during load shorting, which will
cause latch-off. In that case, a Schottky diode from FB pin
to the ground is recommended.
Bias Filter
A small 10 ? resistor is recommended from the input supply
to the bias pin along with a small 0.1μF ceramic capacitor
from bias to ground. This will bypass the high frequency
noise generated by the violent switching of high currents
from reaching the internal reference and control circuitry.
Tantalum and electrolytic capacitors are not recommended
for the bias, these types of capacitors lose their ability to
filter at high frequencies.
March 2009
13
M9999-030209-C
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J0K-EY-F4 | CONVERTER MOD DC/DC 40V 50W |
| LGNW6121MELZ30 | CAP ALUM 120UF 420V 20% SNAP |
| MAX6464UK40+T | IC VOLT DETECTOR LP SOT23-5 |
| LT3462AES6#TRMPBF | IC REG INV ADJ 0.25A TSOT23-6 |
| MAX6464UK41+T | IC VOLT DETECTOR LP SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC4744YTSE TR | 功能描述:直流/直流开关调节器 4 MHz Dual 2A Integrated Switch Buck Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC4782 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1.8 MHz Dual 2A Integrated Switch Buck Regulator |
| MIC4782YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1.8 MHz Dual 2A Integrated Switch Buck Regulator |
| MIC4782YML TR | 功能描述:直流/直流开关调节器 1.8MHz, Dual 2A Buck Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC4782YML-TR | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.6V 2 Output 2A 16-VFQFN Exposed Pad, 16-MLF? 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:2 电压 - 输入（最小值）:3V 电压 - 输入（最大值）:6V 电压 - 输出（最小值/固定）:0.6V 电压 - 输出（最大值）:6V 电流 - 输出:2A 频率 - 开关:1.8MHz 同步整流器:无 工作温度:-20°C ~ 125°C（TJ） 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘，16-MLF? 供应商器件封装:16-MLF?（4x4） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。