参数资料
型号: MIC5162YMM
厂商: Micrel Inc
文件页数: 12/24页
文件大小: 0K
描述: IC CTRLR REG DUAL HS TERM 10MSOP
标准包装: 100
应用: 控制器,DDR3,GDDR3/4/5
输入电压: 1.35 V ~ 6 V
输出数: 1
输出电压: 可编程
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
供应商设备封装: 10-MSOP
包装: 管件
产品目录页面: 1093 (CN2011-ZH PDF)
其它名称: 576-1820-5
MIC5162YMM-ND
Micrel, Inc.
PCB Layout Guideline
Warning!!! To minimize EMI and output noise, follow
Output Capacitor
MIC5162
Place the IC close to the point of load (POL).
these layout recommendations.
PCB Layout is critical to achieve reliable, stable and
efficient performance. A ground plane is required to
control EMI and minimize the inductance in power,
signal and return paths.
The following guidelines should be followed to insure
proper operation of the MIC5162 controller application.
IC and MOSFET
?
?
?
?
Use a wide trace to connect the output capacitor
ground terminal to the input capacitor ground
terminal.
Phase margin will change as the output capacitor
value and ESR changes. Contact the factory if the
output capacitor is different from what is shown in
the BOM.
The feedback trace should be separate from the
power trace and connected as close as possible to
the output capacitor. Sensing a long high current
?
?
?
The trace connecting controller drive pins to
MOSFETs gates should be short and wide to avoid
oscillations. These oscillations are the result of tank
circuit formed by trace inductance and gate
capacitance.
Use fat traces to route the input and output power
lines.
Signal and power grounds should be kept separate
load trace can degrade the DC load regulation.
and connected at only one location.
Input Capacitor
?
?
?
?
?
?
?
?
?
Place the input capacitor next.
Place the input capacitors on the same side of the
board and as close to the MOSFET and IC as
possible.
Place a ceramic bypass capacitor next to MOSFET.
Keep both the VDDQ and GND connections short.
Place several vias to the ground plane close to the
input capacitor ground terminal, but not between the
input capacitors and MOSFET.
Use either X7R or X5R dielectric input capacitors.
Do not use Y5V or Z5U type capacitors.
Do not replace the ceramic input capacitor with any
other type of capacitor. Any type of capacitor can be
placed in parallel with the input capacitor.
If a Tantalum input capacitor is placed in parallel
with the input capacitor, it must be recommended for
switching regulator applications and the operating
voltage must be derated by 50%.
In “Hot-Plug” applications, a Tantalum or Electrolytic
bypass capacitor must be used to limit the over-
voltage spike seen on the input supply with power is
suddenly applied.
March 2010
12
M9999-033110
相关PDF资料
PDF描述
AYM12DTBD CONN EDGECARD 24POS R/A .156 SLD
35USC4700MEFCSN22X25 CAP ALUM 4700UF 35V 20% SNAP-IN
ASC07DRTH-S734 CONN EDGECARD 14POS DIP .100 SLD
VE-J4D-CY-S CONVERTER MOD DC/DC 85V 50W
VE-J2N-EX-F4 CONVERTER MOD DC/DC 18.5V 75W
相关代理商/技术参数
参数描述
MIC5162YMM TR 功能描述:低压差稳压器 - LDO High Speed Termination Regulator Controller -(Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MIC5163_09 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual Regulator Controller for DDR3 GDDR3/4/5 Memory Termination
MIC5163YMM 功能描述:低压差稳压器 - LDO Dual Regulator Controller for DDR2/3 Termination RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MIC5163YMM TR 功能描述:低压差稳压器 - LDO Dual Regulator Controller for DDR2/3 Termination RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MIC5164 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual Regulator Controller for DDR3 GDDR3/4/5 Memory and High-Speed Bus Termination