- 您现在的位置：买卖IC网 > PDF目录13211 > MIC5162YMM (Micrel Inc)IC CTRLR REG DUAL HS TERM 10MSOP PDF资料下载
参数资料
| 型号： | MIC5162YMM |
| 厂商： | Micrel Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR REG DUAL HS TERM 10MSOP |
| 标准包装： | 100 |
| 应用： | 控制器，DDR3，GDDR3/4/5 |
| 输入电压： | 1.35 V ~ 6 V |
| 输出数： | 1 |
| 输出电压： | 可编程 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 1093 (CN2011-ZH PDF) |
| 其它名称： | 576-1820-5 MIC5162YMM-ND |
Micrel, Inc.
Application Information
High performance memory requires high speed
signaling. This means special attention must be paid to
maintain signal integrity. Bus termination provides a
means to increase signaling speed while maintaining
good signal integrity. An example of bus termination is
the Series Stub Termination Logic or SSTL. Figure 1 is
an example of an SSTL 2 single ended series parallel
terminated output. SSTL 2 is a JEDEC signaling
standard operating off a 2.5V supply. It consists of a
series resistor (R S ) and a terminating resistor (R T ).
Values of R S range between 10 to 30 with a typical of
22 , while R T ranges from 22 to 28 with a typical
value of 25 . V REF must maintain 1/2 VDD with a ±1%
tolerance, while V TT will dynamically sink and source
current to maintain a termination voltage of ±40mV from
the V REF line under all conditions. This method of bus
termination reduces common mode noise, settling time,
voltage swings, EMI/RFI and improves slew rates.
The MIC5162 is a high performance linear controller,
utilizing scalable N-Channel MOSFETs to provide
JEDEC-compliant bus termination. Termination is
achieved by dividing down the V DDQ voltage by half,
providing the reference (V REF ) voltage. An internal error
amplifier compares the termination voltage (V TT ) and
V REF , controlling 2 external N-Channel MOSFETs to sink
and source current to maintain a termination voltage
(V TT ) equal to V REF . The N-Channels receive their
enhancement voltage from a separate V CC pin on the
device.
Although this document focuses mostly on SSTL, the
MIC5162 is also capable of providing bus terminations
for SCSI, GTL, HSTL, LV-TTL, Rambus, LV-PECL,
DDR, DDR2, DDR3 memory termination and other
systems.
MIC5162
V DDQ
The V DDQ pin on the MIC5162 provides the source
current through the high-side N-Channel and the
reference voltage to the device. The MIC5162 can
operate at V DDQ voltages as low as 1.35V. Due to the
possibility of large transient currents being sourced from
this line, significant bypass capacitance will aid in
performance by improving the source impedance at
higher frequencies. Since the reference is simply V DDQ /2,
perturbations on the V DDQ will also appear at half the
amplitude on the reference. For this reason, low ESR
capacitors such as ceramics or OS-CON are
recommended on V DDQ .
V TT
V TT is the actual termination point. V TT is regulated to
V REF . Due to high speed signaling, the load current seen
by V TT is constantly changing. To maintain adequate
large signal transient response, large OS-CON and
ceramics are recommended on V TT . The proper
combination and placement of the OS-CON and ceramic
capacitors is important to reduce both ESR and ESL
such that high-current and high-speed transients do not
exceed the dynamic voltage tolerance requirement of
V TT . The larger OS-CON capacitors provide bulk charge
storage while the smaller ceramic capacitors provide
current during the fast edges of the bus transition. Using
several smaller ceramic capacitors distributed near the
termination resistors is typically important to reduce the
effects of PCB trace inductance.
V REF
Two resistors dividing down the V DDQ voltage provide
V REF (Figure 3). The resistors are valued at around
17k . A minimum capacitor value of 120pF from V REF to
ground is required to remove high frequency signals
reflected from the source. Large capacitance values
(>1500pF) should be avoided. Values greater than
1500pF slow down V REF and detract from the reference
voltage’s ability to track V DDQ during high speed load
transients.
Figure 1. SSTL-2 Termination
Figure 2. MIC5162 as a DDR Memory Termination
for 3.5A Application
March 2010
7
M9999-033110
相关PDF资料 |
PDF描述 |
|---|---|
| AYM12DTBD | CONN EDGECARD 24POS R/A .156 SLD |
| 35USC4700MEFCSN22X25 | CAP ALUM 4700UF 35V 20% SNAP-IN |
| ASC07DRTH-S734 | CONN EDGECARD 14POS DIP .100 SLD |
| VE-J4D-CY-S | CONVERTER MOD DC/DC 85V 50W |
| VE-J2N-EX-F4 | CONVERTER MOD DC/DC 18.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5162YMM TR | 功能描述:低压差稳压器 - LDO High Speed Termination Regulator Controller -(Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5163_09 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual Regulator Controller for DDR3 GDDR3/4/5 Memory Termination |
| MIC5163YMM | 功能描述:低压差稳压器 - LDO Dual Regulator Controller for DDR2/3 Termination RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5163YMM TR | 功能描述:低压差稳压器 - LDO Dual Regulator Controller for DDR2/3 Termination RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5164 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual Regulator Controller for DDR3 GDDR3/4/5 Memory and High-Speed Bus Termination |
发布紧急采购，3分钟左右您将得到回复。