- 您现在的位置：买卖IC网 > PDF目录80482 > MM908E624ACEW/R2 (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 32 MHz, MICROCONTROLLER, PDSO54 PDF资料下载
参数资料
| 型号： | MM908E624ACEW/R2 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 32 MHz, MICROCONTROLLER, PDSO54 |
| 封装： | 0.65 MM PITCH, ROHS COMPLIANT, SOIC-54 |
| 文件页数： | 14/39页 |
| 文件大小： | 702K |
| 代理商： | MM908E624ACEW/R2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
908E624
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Figure 12. Stop Mode/Wake-up Procedure
ANALOG DIE INPUTS/OUTPUTS
High Side Output Pins HS1 and HS2
These are two high side switches used to drive loads such
as relays or lamps. They are protected with over-temperature
and current limit (over-current) and include an active internal
clamp circuitry for inductive load drive. Control is done using
the SPI Control register. PWM capability is offered through
the PWMIN input pin.
The high side switch is turned on if both the HSxON bit in
the SPI Control register is set and the PWMIN input is HIGH
(refer to Figure 13, page 22). In order to have HS1 on, the
PWMIN must be HIGH and bit HS1ON must be set. The
same applies to the HS2 output.
If no PWM control is required, PWMIN must be connected
to the VDD pin.
Current Limit (Over-current) Protection
These high side switches feature current limit to protect
them against over-current and short circuit conditions.
Over-temperature Protection
If an over-temperature condition occurs on any of the three
high side switches, all high side switches (HS1, HS2, and
HS3) are turned off and latched off. The failure is reported by
the HSST bit in the SPI Control register.
From Reset
initialize
operate
SPI:
2x STOP
Command
STOP
IRQ
interrupt
?
SPI: reason for
interrupt
operate
Switch to VREG
low current mode
Assert IRQ
Switch to VREG
high current mode
MCU
Power Die
Wake-up on
LIN or L1, L2?
相关PDF资料 |
PDF描述 |
|---|---|
| MSP430CG4617IPZ | 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP100 |
| MC9328MX21SCVK | 32-BIT, 266 MHz, MICROPROCESSOR, PBGA289 |
| MC7457RX1200LC | 32-BIT, 1200 MHz, RISC PROCESSOR, CBGA483 |
| MC3S12HZ32J3CAA | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| MC9S12HZ64J3MAA | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MM908E624ACPEW | 功能描述:8位微控制器 -MCU 3 HIGH SIDE SWITCH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E624ACPEWR2 | 功能描述:8位微控制器 -MCU 3 HIGH SIDE DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E624AYEW | 功能描述:开关 IC - 各种 TRIPLE HIGH SIDE SWITCH RoHS:否 制造商:Fairchild Semiconductor 开启电阻（最大值）: 电源电压-最大:4.4 V 电源电压-最小:2.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WLCSP-9 封装:Reel |
| MM908E624AYEW/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Triple High Side Switch with Embedded MCU and LIN Serial Communicationfor Relay Drivers |
| MM908E624AYEWR2 | 功能描述:开关 IC - 各种 TRIPLE HIGH SIDE SWITCH RoHS:否 制造商:Fairchild Semiconductor 开启电阻（最大值）: 电源电压-最大:4.4 V 电源电压-最小:2.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WLCSP-9 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。