参数资料
型号: MM908E624ACEW/R2
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 32 MHz, MICROCONTROLLER, PDSO54
封装: 0.65 MM PITCH, ROHS COMPLIANT, SOIC-54
文件页数: 16/39页
文件大小: 702K
代理商: MM908E624ACEW/R2
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
908E624
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
The LIN pin offers high susceptibility immunity level from
external disturbance, guaranteeing communication during
external disturbance.
The LIN transmitter circuitry is enabled in Normal and
Normal Request mode.
An over-current condition (e.g. LIN bus short to VBAT) or a
over-temperature in the output low side FET will shutdown
the transmitter and set the LINFAIL flag in the SPI Status
Register.
For improved performance and safe behavior in case of
LIN bus short to Ground or LIN bus leakage during low power
mode the internal pull-up resistor on the LIN pin can be
disconnected, with the LIN-PU bit in the SPI Control Register,
and a small current source keeps the LIN bus at recessive
level. In case of a LIN bus short to GND, this feature will
reduce the current consumption in STOP and SLEEP modes.
Figure 15. LIN Interface
TXD Pin
The TXD pin is the MCU interface to control the state of the
LIN transmitter (see Figure 2, page 2). When TXD is LOW,
the LIN pin is low (dominant state). When TXD is HIGH, the
LIN output MOSFET is turned off (recessive state). The TXD
pin has an internal pull-up current source in order to set the
LIN bus to recessive state in the event, for instance, the
microcontroller could not control it during system power-up or
power-down.
RXD Pin
The RXD transceiver pin is the MCU interface, which
reports the state of the LIN bus voltage. LIN HIGH (recessive
state) is reported by a high level on RXD, LIN LOW (dominant
state) by a low level on RXD.
STOP Mode and Wake-up Feature
During STOP mode operation the transmitter of the
physical layer is disabled. In case the bit LIN-PU was set in
the Stop mode sequence the internal pull-up resistor is
disconnected from VSUP and a small current source keeps
the LIN pin in recessive state. The receiver is still active and
able to detect wake-up events on the LIN bus line.
A dominant level longer than tPROPWL followed by an rising
edge will generate a wake-up interrupt and set the LINWF
flag in the SPI Status Register. Also see Figure 9, page 15.
SLEEP Mode and Wake-up Feature
During SLEEP mode operation the transmitter of the
physical layer is disabled. In case the bit LIN-PU was set in
the Sleep mode sequence the internal pull-up resistor is
Control
Re
ce
iv
er
RXD
TXD
GND
VSUP1
Slope
Control
30k
2A
LIN bus
LINSL2:1
MODE2:1
LINFAIL
LINWU
Wake-up
Filter
LIN-PU
相关PDF资料
PDF描述
MSP430CG4617IPZ 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQFP100
MC9328MX21SCVK 32-BIT, 266 MHz, MICROPROCESSOR, PBGA289
MC7457RX1200LC 32-BIT, 1200 MHz, RISC PROCESSOR, CBGA483
MC3S12HZ32J3CAA 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80
MC9S12HZ64J3MAA 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
MM908E624ACPEW 功能描述:8位微控制器 -MCU 3 HIGH SIDE SWITCH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MM908E624ACPEWR2 功能描述:8位微控制器 -MCU 3 HIGH SIDE DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MM908E624AYEW 功能描述:开关 IC - 各种 TRIPLE HIGH SIDE SWITCH RoHS:否 制造商:Fairchild Semiconductor 开启电阻(最大值): 电源电压-最大:4.4 V 电源电压-最小:2.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WLCSP-9 封装:Reel
MM908E624AYEW/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Triple High Side Switch with Embedded MCU and LIN Serial Communicationfor Relay Drivers
MM908E624AYEWR2 功能描述:开关 IC - 各种 TRIPLE HIGH SIDE SWITCH RoHS:否 制造商:Fairchild Semiconductor 开启电阻(最大值): 电源电压-最大:4.4 V 电源电压-最小:2.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WLCSP-9 封装:Reel