- 您现在的位置：买卖IC网 > PDF目录48741 > MMBD701LT1 (MOTOROLA INC) SILICON, VHF-UHF BAND, MIXER DIODE, TO-236AB PDF资料下载
参数资料
| 型号： | MMBD701LT1 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 射频混频器 |
| 英文描述： | SILICON, VHF-UHF BAND, MIXER DIODE, TO-236AB |
| 文件页数： | 3/4页 |
| 文件大小： | 89K |
| 代理商： | MMBD701LT1 |
MBD701 MMBD701LT1
3
Motorola Small–Signal Transistors, FETs and Diodes Device Data
INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
SOT–23
mm
inches
0.037
0.95
0.037
0.95
0.079
2.0
0.035
0.9
0.031
0.8
SOT–23 POWER DISSIPATION
The power dissipation of the SOT–23 is a function of the
drain pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
by TJ(max), the maximum rated junction temperature of the
die, R
θJA, the thermal resistance from the device junction to
ambient, and the operating temperature, TA. Using the
values provided on the data sheet for the SOT–23 package,
PD can be calculated as follows:
PD =
TJ(max) – TA
R
θJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25°C, one can
calculate the power dissipation of the device which in this
case is 200 milliwatts for the SOT–23 package.
PD =
150
°C – 25°C
625
°C/W
= 200 milliwatts
The 556
°C/W for the SOT–23 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 225 milliwatts. There
are other alternatives to achieving higher power dissipation
from the SOT–23 package. Another alternative would be to
use a ceramic substrate or an aluminum core board such as
Thermal Clad
. Using a board material such as Thermal
Clad, an aluminum core board, the power dissipation can be
doubled using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10
°C.
The soldering temperature and time shall not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the maximum
temperature gradient shall be 5
°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
相关PDF资料 |
PDF描述 |
|---|---|
| MMBZ5233BD87Z | 6 V, 0.35 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| MMBZ5228BD87Z | 3.9 V, 0.35 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| MMBZ5232BD87Z | 5.6 V, 0.35 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| MMBZ5237BD87Z | 8.2 V, 0.35 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
| MMBZ5241B | 11 V, 0.35 W, SILICON, UNIDIRECTIONAL VOLTAGE REGULATOR DIODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MMBD701LT1G | 功能描述:肖特基二极管与整流器 70V 200mW Dual Common Anode RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| MMBD701LT3 | 功能描述:肖特基二极管与整流器 70V 200mW Dual RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| MMBD701LT3G | 功能描述:DIODE SCHOTTKY 70V SOT-23 RoHS:是 类别:分离式半导体产品 >> RF 二极管 系列:- 标准包装:3,000 系列:- 二极管类型:PIN - 单 电压 - 峰值反向(最大):50V 电流 - 最大:50mA 电容@ Vr, F:0.4pF @ 50V，1MHz 电阻@ Vr, F:4.5 欧姆 @ 10mA，100MHz 功率耗散（最大）:100mW 封装/外壳:SC-70，SOT-323 供应商设备封装:3-MCP 包装:带卷 (TR) |
| MMBD717 | 制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:SURFACE MOUNT SCHOTTKY DIODES |
| MMBD717_09 | 制造商:PANJIT 制造商全称:Pan Jit International Inc. 功能描述:SURFACE MOUNT SCHOTTKY DIODES |
发布紧急采购，3分钟左右您将得到回复。