- 您现在的位置：买卖IC网 > PDF目录183240 > MP1531DQ-LF-Z (MONOLITHIC POWER SYSTEMS INC) 0.65 A SWITCHING REGULATOR, 300 kHz SWITCHING FREQ-MAX, QCC16 PDF资料下载
参数资料
| 型号： | MP1531DQ-LF-Z |
| 厂商： | MONOLITHIC POWER SYSTEMS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.65 A SWITCHING REGULATOR, 300 kHz SWITCHING FREQ-MAX, QCC16 |
| 封装： | 3 X 3 MM, ROHS COMPLIANT, MO-220VEED-4, QFN-16 |
| 文件页数： | 12/12页 |
| 文件大小： | 287K |
| 代理商： | MP1531DQ-LF-Z |
MP1531 – LOW POWER, TRIPLE OUTPUT STEP-UP PLUS CHARGE PUMP FOR TFT BIAS
MP1531 Rev. 1.3
www.MonolithicPower.com
9
12/4/2009
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2009 MPS. All Rights Reserved.
To insure stable operation place the input
capacitor as close to the IC as possible.
Alternately a smaller high quality 0.1μF ceramic
capacitor may be placed closer to the IC if the
larger capacitor is placed further away.
Selecting the Rectifier Diodes
Schottky diodes are recommended for most
applications because of their fast recovery time
and low forward voltage. Use Schottky diodes
with a current rating equal to or greater than 4
times the average output current, and a voltage
rating at least 1.5 times VGH for the positive
charge-pump and VGL for the negative charge-
pump. 100mA Schottky diodes such as Central
Semiconductor CMPSH-3 are recommended
for low current charge-pump circuits.
Selecting the Output Capacitor of the Step-
Up Converter
The output capacitor is required to maintain the
DC output voltage. Low ESR capacitors are
preferred to keep the output voltage ripple to a
minimum. The characteristics of the output
capacitor also affect the stability of the
regulation control system. A 10-22μF ceramic
capacitor works well in most applications. In the
case of ceramic capacitors, the impedance of
the capacitor at the switching frequency is
dominated by the capacitance, and so the
output voltage ripple is mostly independent of
the ESR. The output voltage ripple is estimated
to be:
SW
MAIN
LOAD
IN
MAIN
RIPPLE
f
2
C
V
I
)
V
(
V
×
Where VRIPPLE is the output ripple voltage, ILOAD
is the load current, and C2 is the capacitance of
the output capacitor of the step-up converter.
Selecting the Number of Charge-Pump
Stages
For highest efficiency, always choose the
lowest number of charge-pump stages that
meets the output requirement.
The number of positive charge-pump stages
NPOS is approximately given by:
()
D
MAIN
DROPOUT
GH
POS
V
2
V
N
×
+
Where VD is the forward voltage drop of the
charge-pump diode, and VDROPOUT is the
dropout margin for the linear regulator. The
positive charge-pump can also be configured
based on VIN for better efficiency. Then the
equation will be:
(
)
D
MAIN
IN
DROPOUT
GH
POS
V
2
V
N
×
+
The number of negative charge-pump stages
NNEG is approximately given by:
D
MAIN
DROPOUT
GL
NEG
V
2
V
N
×
+
Use VDROPOUT = 0.5V for positive charge-pump
and VDROPOUT = 0.15V for negative charge-pump.
Selecting the Flying Capacitor in Charge-
Pump Stages
Increasing the flying capacitor CX values
increases the output current capability. A
0.33μF ceramic capacitor works well in most
low current applications. The flying capacitor’s
voltage rating must exceed the following:
MAIN
CX
V
N
V
×
>
Where N is the stage number in which the flying
capacitor appears.
Step-Up Converter Compensation
The MP1531 uses current-mode control which
unlike voltage mode has only a single pole roll
off due to the output filter. The DC gain (AVDC) is
equated from the product of current control to
output gain (AVCSCONTROL), error amplifier gain
(AVEA), and the feedback divider.
1
FB
EA
CSCONTROL
DC
A
Av
A
Av
×
=
LOAD
IN
CSCONTROL
I
V
4
A
×
=
MAIN
1
FB
1
FB
V
A
=
MAIN
LOAD
1
FB
IN
DC
V
I
V
1600
Av
×
=
The output filter pole is given in hertz by:
2
C
V
I
f
MAIN
LOAD
FILTERPOLE
×
π
=
相关PDF资料 |
PDF描述 |
|---|---|
| MP2-H096-43S1-S-TG30 | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| MP2-H096-43S1-S-TG | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| MP2-H096-43S1-S-TR30 | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| MP2-H096-43S1-S-TR40B | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| MP2-H096-43S2-S-FJ | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MP154 | 功能描述:桥式整流器 15A 400V RoHS:否 制造商:Vishay 产品:Single Phase Bridge 峰值反向电压:1000 V 最大 RMS 反向电压: 正向连续电流:4.5 A 最大浪涌电流:450 A 正向电压下降:1 V 最大反向漏泄电流:10 uA 功率耗散: 最大工作温度:+ 150 C 长度:30.3 mm 宽度:4.1 mm 高度:20.3 mm 安装风格:Through Hole 封装 / 箱体:SIP-4 封装:Tube |
| MP1540 | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:1.3MHz,18V Step-Up Converter |
| MP1540DJ-LF-P | 功能描述:开关变换器、稳压器与控制器 1.3MHz, 18V Step-up Converter RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MP1540DJ-LF-Z | 功能描述:开关变换器、稳压器与控制器 1.3MHz, 18V Step-up Converter RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MP1541 | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:1.3MHz Boost Converter |
发布紧急采购，3分钟左右您将得到回复。