- 您现在的位置：买卖IC网 > PDF目录183240 > MP1531DQ-LF-Z (MONOLITHIC POWER SYSTEMS INC) 0.65 A SWITCHING REGULATOR, 300 kHz SWITCHING FREQ-MAX, QCC16 PDF资料下载
参数资料
| 型号： | MP1531DQ-LF-Z |
| 厂商： | MONOLITHIC POWER SYSTEMS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.65 A SWITCHING REGULATOR, 300 kHz SWITCHING FREQ-MAX, QCC16 |
| 封装： | 3 X 3 MM, ROHS COMPLIANT, MO-220VEED-4, QFN-16 |
| 文件页数： | 9/12页 |
| 文件大小： | 287K |
| 代理商： | MP1531DQ-LF-Z |
MP1531 – LOW POWER, TRIPLE OUTPUT STEP-UP PLUS CHARGE PUMP FOR TFT BIAS
MP1531 Rev. 1.3
www.MonolithicPower.com
6
12/4/2009
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2009 MPS. All Rights Reserved.
Step-Up Converter
The 250KHz fixed-frequency step-up converter
employs a current-mode control architecture
that maximizes loop bandwidth to provide fast-
transient responses needed for TFT LCD
drivers. High switching frequency allows for
smaller inductors and capacitors minimizing
board space and thickness.
Linear Regulators
The positive linear regulator (GH) uses a
P-Channel pass element to drop the input
voltage down to the regulated output voltage.
The feedback of the positive linear regulator is
a
conventional
error
amplifier
with
the
regulation threshold at 1.25V.
The negative linear regulator (GL) uses a
N-Channel pass element to raise the negative
input voltage up to the regulated output voltage.
The feedback threshold for the negative linear
regulator is ground. The resistor string goes
from REF (1.25V) to FB2 and from FB2 to GL to
set the negative output voltage, VGL.
The difference between the voltage at IN3 and
the voltage at IN2 is limited to 60V abs. max.
Fault Sensing and Timer
Each of the 3 outputs has an internal
comparator that monitors its respective output
voltage by measuring the voltage at its
respective FB input. When any FB input
indicates that the output voltage is below
approximately 80% of the correct regulation
voltage, the fault timer enables and the RDY
pin goes high impedance. The fault timer uses
the same CT capacitor as the soft-start
sequencer. If any fault persists to the end of the
fault timer (One CT cycle is 6ms for a 10nF
capacitor), all outputs are disabled. Once the
outputs are shut down due to the fault timer, the
MP1531 must be re-enabled by either cycling
EN or by cycling the input power. When re-
enabled, the MP1531 cycles through the normal
power-on sequence. If the fault persists for less
than the fault timer period, RDY will be pulled
low and the part will function as though no fault
has occurred.
Power-On Sequencing and Soft-Start
The MP1531 automatically sequences its
outputs at startup. When EN goes from low to
high, or if EN is held high and the input voltage
VIN rises above the under-voltage lockout
threshold, the outputs turn on in the following
sequence:
1. Step-up converter
2. Negative linear regulator (GL)
3. Positive linear regulator (GH)
Each output turns on with a soft-start voltage
ramp. The soft-start ramp period is set by the
timing capacitor connected between CT and
GND. A 10nF capacitor at CT sets the soft-start
ramp period to 6ms. The timing diagram is
shown in Figure 2.
After the MP1531 is enabled, the power-on
reset spans three periods of the CT ramp. First
the step-up converter is powered up with
reference to the CT ramp and allowed one
period of the CT ramp to settle. Next the
negative linear regulator (GL) is soft-started by
ramping REF, which coincides with the CT
ramp, and also allowed one CT ramp period to
settle.
The positive linear regulator (GH) is then
soft-started and allowed to settle in one period
of CT ramp. Nine periods of the CT ramp have
occurred since the chip enabled. If all outputs
are in regulation (>80%), the CT will stop
ramping and be held at ground. The RDY pin
will be pulled down to an active low. If any FB
voltage remains below regulation (<80%) after
the nine CT periods, RDY will remain high and
CT will begin its fault timer pulse.
相关PDF资料 |
PDF描述 |
|---|---|
| MP2-H096-43S1-S-TG30 | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| MP2-H096-43S1-S-TG | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| MP2-H096-43S1-S-TR30 | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| MP2-H096-43S1-S-TR40B | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| MP2-H096-43S2-S-FJ | 96 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MP154 | 功能描述:桥式整流器 15A 400V RoHS:否 制造商:Vishay 产品:Single Phase Bridge 峰值反向电压:1000 V 最大 RMS 反向电压: 正向连续电流:4.5 A 最大浪涌电流:450 A 正向电压下降:1 V 最大反向漏泄电流:10 uA 功率耗散: 最大工作温度:+ 150 C 长度:30.3 mm 宽度:4.1 mm 高度:20.3 mm 安装风格:Through Hole 封装 / 箱体:SIP-4 封装:Tube |
| MP1540 | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:1.3MHz,18V Step-Up Converter |
| MP1540DJ-LF-P | 功能描述:开关变换器、稳压器与控制器 1.3MHz, 18V Step-up Converter RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MP1540DJ-LF-Z | 功能描述:开关变换器、稳压器与控制器 1.3MHz, 18V Step-up Converter RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MP1541 | 制造商:MPS 制造商全称:Monolithic Power Systems 功能描述:1.3MHz Boost Converter |
发布紧急采购，3分钟左右您将得到回复。