参数资料
型号: MPC7410RX400LE
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, 400 MHz, RISC PROCESSOR, CBGA360
封装: 25 X 25 MM, 3.20 MM HEIGHT, 1.27 MM PITCH, CERAMIC, BGA-360
文件页数: 32/56页
文件大小: 864K
代理商: MPC7410RX400LE
MPC7410 RISC Microprocessor Hardware Specifications, Rev. 6.1
38
Freescale Semiconductor
System Design Information
8.4 Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level
through a resistor. Unused active low inputs should be tied to OVDD. Unused active high inputs should be connected
to GND. All NC (no connect) signals must remain unconnected.
Power and ground connections must be made to all external VDD, OVDD, L2OVDD, and GND pins of the MPC7410.
Note that power must be supplied to L2OVDD even if the L2 interface of the MPC7410 will not be used; the
remainder of the L2 interface may be left unterminated.
8.5 Output Buffer DC Impedance
The MPC7410 60x and L2 I/O drivers are characterized over process, voltage, and temperature. To measure Z0, an
external resistor is connected from the chip pad to OVDD or GND. Then, the value of each resistor is varied until
the pad voltage is OVDD/2 (see Figure 23).
The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. When
data is held low, SW2 is closed (SW1 is open), and RN is trimmed until the voltage at the pad equals (L2)OVDD/2.
RN then becomes the resistance of the pull-down devices. When data is held high, SW1 is closed (SW2 is open), and
RP is trimmed until the voltage at the pad equals (L2)OVDD/2. RP then becomes the resistance of the pull-up devices.
RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2.
Figure 23 describes the driver impedance measurement circuit described above.
Figure 23. Driver Impedance Measurement Circuit
Alternately, the following is another method to determine the output impedance of the MPC7410. A voltage source,
Vforce, is connected to the output of the MPC7410, as in Figure 24. Data is held low, the voltage source is set to a
value that is equal to (L2)OVDD/2, and the current sourced by Vforce is measured. The voltage drop across the
pull-down device, which is equal to (L2)OVDD/2, is divided by the measured current to determine the output
impedance of the pull-down device, RN. Similarly, the impedance of the pull-up device is determined by dividing
the voltage drop of the pull-up, (L2)OVDD/2, by the current sank by the pull-up when the data is high and Vforce is
equal to (L2)OVDD/2. This method can be employed with either empirical data from a test setup or with data from
simulation models, such as IBIS.
OVDD
OGND
RP
RN
Pad
Data
SW1
SW2
相关PDF资料
PDF描述
MPC745BPX400LE 32-BIT, 400 MHz, RISC PROCESSOR, PBGA255
MPC745BPX350LE 32-BIT, 350 MHz, RISC PROCESSOR, PBGA255
MPC755BRX400LE 32-BIT, 400 MHz, RISC PROCESSOR, CBGA360
MPC750PRX366LE 32-BIT, 366 MHz, RISC PROCESSOR, CBGA360
MPC750PRX400LE 32-BIT, 400 MHz, RISC PROCESSOR, CBGA360
相关代理商/技术参数
参数描述
MPC7410RX400NE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:MPC7410 RISC Microprocessor Hardware Specifications Addendum
MPC7410RX450NE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:MPC7410 RISC Microprocessor Hardware Specifications Addendum
MPC7410RX500LE 功能描述:IC MPU 32BIT 500MHZ PPC 360-CBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC74xx 标准包装:2 系列:MPC8xx 处理器类型:32-位 MPC8xx PowerQUICC 特点:- 速度:133MHz 电压:3.3V 安装类型:表面贴装 封装/外壳:357-BBGA 供应商设备封装:357-PBGA(25x25) 包装:托盘
MPC7410THX400LE 功能描述:微处理器 - MPU NT HITCE RV1.4 1.8V -40C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MPC7410THX400NE 制造商:Freescale Semiconductor 功能描述:MPU MPC74XX RISC 64BIT 0.18UM 400MHZ 1.8V/2.5V/3.3V 360FCCBG - Bulk