参数资料
型号: MPC8548VUAVGB
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, 1500 MHz, MICROPROCESSOR, CBGA783
封装: 29 X 29 MM, 1 MM PITCH, FLIP CHIP, LEAD FREE, CERAMIC, BGA-783
文件页数: 36/142页
文件大小: 1504K
代理商: MPC8548VUAVGB
MPC8548E PowerQUICC III Integrated Processor Hardware Specifications, Rev. 5
130
Freescale Semiconductor
System Design Information
21.4
SerDes Block Power Supply Decoupling Recommendations
The SerDes block requires a clean, tightly regulated source of power (SVDD and XVDD) to ensure low
jitter on transmit and reliable recovery of data in the receiver. An appropriate decoupling scheme is
outlined below.
Only surface mount technology (SMT) capacitors should be used to minimize inductance. Connections
from all capacitors to power and ground should be done with multiple vias to further reduce inductance.
First, the board should have at least 10
× 10-nF SMT ceramic chip capacitors as close as possible
to the supply balls of the device. Where the board has blind vias, these capacitors should be placed
directly below the chip supply and ground connections. Where the board does not have blind vias,
these capacitors should be placed in a ring around the device as close to the supply and ground
connections as possible.
Second, there should be a 1-F ceramic chip capacitor from each SerDes supply (SVDD and
XVDD) to the board ground plane on each side of the device. This should be done for all SerDes
supplies.
Third, between the device and any SerDes voltage regulator there should be a 10-F, low
equivalent series resistance (ESR) SMT tantalum chip capacitor and a 100-F, low ESR SMT
tantalum chip capacitor. This should be done for all SerDes supplies.
21.5
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. All unused active low inputs should be tied to VDD, TVDD, BVDD, OVDD, GVDD, and LVDD, as
required. All unused active high inputs should be connected to GND. All NC (no-connect) signals must
remain unconnected. Power and ground connections must be made to all external VDD, TVDD, BVDD,
OVDD, GVDD, LVDD, and GND pins of the device.
21.6
Pull-Up and Pull-Down Resistor Requirements
The MPC8548E requires weak pull-up resistors (2–10 k
Ω is recommended) on open drain type pins
including I2C pins and PIC (interrupt) pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in Figure 62. Care must be taken to ensure that these pins are maintained at a valid deasserted
state under normal operating conditions as most have asynchronous behavior and spurious assertion will
give unpredictable results.
The following pins must not be pulled down during power-on reset: TSEC3_TXD[3], HRESET_REQ,
TRIG_OUT/READY/QUIESCE, MSRCID[2:4], ASLEEP. The DMA_DACK[0:1], and TEST_SEL/
TEST_SEL pins must be set to a proper state during POR configuration. Refer to the pinlist table of the
individual device for more details
Refer to the PCI 2.2 specification for all pull ups required for PCI.
相关PDF资料
PDF描述
MC9S08DN16CLC 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP32
MK50X256CMB100R 32-BIT, FLASH, 100 MHz, RISC MICROCONTROLLER, PBGA81
M102E0200.0000DK 200 MHz, OTHER CLOCK GENERATOR, MDIP24
MK3723D 14 MHz, OTHER CLOCK GENERATOR, PDSO8
MK3717S 27 MHz, OTHER CLOCK GENERATOR, PDSO8
相关代理商/技术参数
参数描述
MPC8548VUAVH 制造商:Freescale Semiconductor 功能描述:MPU RISC 32BIT CMOS 1.5GHZ 1.8V/2.5V/3.3V 783FCCBGA - Bulk
MPC8548VUAVK 制造商:Freescale Semiconductor 功能描述:PQ38 8548 PB-FREE - Bulk
MPC8555CDS 功能描述:开发板和工具包 - 其他处理器 CDS EVAL BOARD FOR 8555 RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压:
MPC8555CDS 制造商:Freescale Semiconductor 功能描述:CDS EVAL BOARD FOR 8555
MPC8555CPXAJD 功能描述:微处理器 - MPU PQ 37 LITE 8555 RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324