参数资料
型号: MSC8144VT800A
厂商: Freescale Semiconductor
文件页数: 64/80页
文件大小: 0K
描述: IC DSP QUAD 800MHZ 783FCBGA
标准包装: 1
系列: StarCore
类型: SC3400 内核
接口: 以太网,I²C,SPI,TDM,UART,UTOPIA
时钟速率: 800MHz
非易失内存: 外部
芯片上RAM: 10.5MB
电压 - 输入/输出: 3.30V
电压 - 核心: 1.00V
工作温度: 0°C ~ 90°C
安装类型: 表面贴装
封装/外壳: 783-BBGA,FCBGA
供应商设备封装: 783-FCPBGA(29x29)
包装: 托盘
Hardware Design Considerations
MSC8144 Quad Core Digital Signal Processor Data Sheet, Rev. 16
Freescale Semiconductor
67
3.3
Clock and Timing Signal Board Layout Considerations
When laying out the system board, use the following guidelines:
Keep clock and timing signal paths as short as possible and route with 50
Ω impedance.
Use a serial termination resistor placed close to the clock buffer to minimize signal reflection. Use the following
equation to compute the resistor value:
Rterm = Rim – Rbuf
where Rim = trace characteristic impedance
Rbuf = clock buffer internal impedance.
Note:
See MSC8144 CLKIN and PCI_CLK_IN Board Layout (AN3440) for an example layout.
3.4
Connectivity Guidelines
Note:
Although the package actually uses a ball grid array, the more conventional term pin is used to denote signal
connections in this discussion.
First, select the pin multiplexing mode to allocate the required I/O signals. Then use the guidelines presented in the following
subsections for board design and connections. The following conventions are used in describing the connectivity requirements:
1.
GND indicates using a 10 k
Ω pull-down resistor (recommended) or a direct connection to the ground plane. Direct
connections to the ground plane may yield DC current up to 50mA through the I/O supply that adds to overall power
consumption.
2.
VDD indicates using a 10 kΩ pull-up resistor (recommended) or a direct connection to the appropriate power supply.
Direct connections to the supply may yield DC current up to 50mA through the I/O supply that adds to overall power
consumption.
3.
Mandatory use of a pull-up or pull-down resistor it is clearly indicated as “pull-up/pull-down”.
4.
NC indicates “not connected” and means do not connect anything to the pin.
5.
The phrase “in use” indicates a typical pin connection for the required function.
Note:
Please see recommendations #1 and #2 as mandatory pull-down or pull-up connection for unused pins in case of
subset interface connection.
3.4.1
DDR Memory Related Pins
This section discusses the various scenarios that can be used with DDR1 and DDR2 memory.
Note:
For information about unused differential/non-differential pins in DDR1/DDR2 modes (that is, unused negative lines
of strobes in DDR1), please refer to Table 51.
3.4.1.1
DDR Interface Is Not Used
Table 51. Connectivity of DDR Related Pins When the DDR Interface Is Not Used
Signal Name
Pin Connection
MDQ[0–31]
NC
MDQS[0–3]
NC
MDQS[0–3]
NC
MA[0–15]
NC
MCK[0–2]
NC
MCK[0–2]
NC
MCS[0–1]
NC
相关PDF资料
PDF描述
MSC8154SVT1000B IC PROCESSOR QUAD DGTL 783FCPBGA
MSC8156TVT1000B IC PROCESSOR QUAD DGTL 783FCPBGA
MSC8251TVT1000B IC DSP SINGLE 1GHZ 783FCPBGA
MSC8254TVT1000B IC DSP QUAD 1GHZ 783FCPBGA
MSC8256TVT1000B IC DSP 6 CORE 1GHZ 783FCPBGA
相关代理商/技术参数
参数描述
MSC8144VT800B 制造商:Freescale Semiconductor 功能描述:DSP 32-Bit 800MHz 800MIPS 783-Pin FCBGA 制造商:Freescale Semiconductor 功能描述:PACSUN REV2.1 NON-E - Bulk 制造商:Freescale Semiconductor 功能描述:ENCRYPTION PACSUN R2.1 783FCPBGA
MSC81450M 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:RF & MICROWAVE TRANSISTORS AVIONICS APPLICATIONS
MSC8151 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Single-Core Digital Signal Processor
MSC8151SAG1000B 制造商:Freescale Semiconductor 功能描述:STARCORE DSP, 1X 1GHZ SC3850 CORES, MAPLE-B ACCELERATOR, DDR - Bulk 制造商:Freescale Semiconductor 功能描述:STARCORE DSP, 1X 1GHZ SC3850 CORES, MAPLE-B ACCELERATOR, DDR - Trays 制造商:Freescale Semiconductor 功能描述:IC DSP 1X 1GHZ SC3850 783FCBGA
MSC8151SVT1000B 功能描述:数字信号处理器和控制器 - DSP, DSC Darwin RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT