收藏本站
参数资料
型号： MSP430C412IRTD
厂商： TEXAS INSTRUMENTS INC
元件分类： 微控制器/微处理器
英文描述： 16-BIT, MROM, 8 MHz, RISC MICROCONTROLLER, PQCC64
封装： PLASTIC, QFN-64
文件页数： 31/58页
文件大小： 1160K
代理商： MSP430C412IRTD
MSP430x41x
MIXED SIGNAL MICROCONTROLLER
SLAS340H MAY 2001 REVISED APRIL 2007
37
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature (unless otherwise
noted) (continued)
Flash Memory
PARAMETER
TEST
CONDITIONS
VCC
MIN
NOM
MAX
UNIT
VCC(PGM/
ERASE)
Program and Erase supply voltage
2.7
3.6
V
fFTG
Flash Timing Generator frequency
257
476
kHz
IPGM
Supply current from DVCC during program
2.7 V/ 3.6 V
3
5
mA
IERASE
Supply current from DVCC during erase
2.7 V/ 3.6 V
3
7
mA
tCPT
Cumulative program time
see Note 1
2.7 V/ 3.6 V
10
ms
tCMErase
Cumulative mass erase time
see Note 2
2.7 V/ 3.6 V
200
ms
Program/Erase endurance
104
105
cycles
tRetention
Data retention duration
TJ = 25°C
100
years
tWord
Word or byte program time
35
tBlock, 0
Block program time for 1st byte or word
30
tBlock, 1-63
Block program time for each additional byte or word
see Note 3
21
t
tBlock, End
Block program end-sequence wait time
see Note 3
6
tFTG
tMass Erase
Mass erase time
5297
tSeg Erase
Segment erase time
4819
NOTES:
1. The cumulative program time must not be exceeded when writing to a 64-byte flash block. This parameter applies to all programming
methods: individual word/byte write and block write modes.
2. The mass erase duration generated by the flash timing generator is at least 11.1ms ( = 5297x1/fFTG,max = 5297x1/476kHz). To
achieve the required cumulative mass erase time the Flash Controller’s mass erase operation can be repeated until this time is met.
(A worst case minimum of 19 cycles are required).
3. These values are hardwired into the Flash Controller’s state machine (tFTG = 1/fFTG).
JTAG Interface
PARAMETER
TEST
CONDITIONS
VCC
MIN
NOM
MAX
UNIT
f
TCK input frequency
see Note 1
2.2 V
0
5
MHz
fTCK
TCK input frequency
see Note 1
3 V
0
10
MHz
RInternal
Internal pull-up resistance on TMS, TCK, TDI/TCLK
see Note 2
2.2 V/ 3 V
25
60
90
k
Ω
NOTES:
1. fTCK may be restricted to meet the timing requirements of the module selected.
2. TMS, TDI/TCLK, and TCK pull-up resistors are implemented in all versions.
JTAG Fuse (see Note 1)
PARAMETER
TEST
CONDITIONS
VCC
MIN
NOM
MAX
UNIT
VCC(FB)
Supply voltage during fuse-blow condition
TA = 25°C
2.5
V
Voltage level on TDI/TCLK for fuse-blow - ’C41x
3.5
3.9
V
VFB
Voltage level on TDI/TCLK for fuse-blow - ’F41x
6
7
V
IFB
Supply current into TDI/TCLK during fuse blow
100
mA
tFB
Time to blow fuse
1
ms
NOTES:
1. Once the fuse is blown, no further access to the MSP430 JTAG/Test and emulation features is possible. The JTAG block is switched
to bypass mode.
相关PDF资料
PDF描述
MSP430C413IRTD 16-BIT, MROM, 8 MHz, RISC MICROCONTROLLER, PQCC64
MSP430F1101AIDW 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20
MSP430F1101IDW 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20
MSP430F1111AIDW 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PDSO20
MSP430F1121AIRGER 16-BIT, FLASH, 8 MHz, RISC MICROCONTROLLER, PQCC24
相关代理商/技术参数
参数描述
MSP430C413 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430C413CY 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430C413IPM 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430C413IRTD 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430-CCRF 功能描述:开发板和工具包 - MSP430 868 / 915MHZ TRANS FOR CC430F5137 RoHS:否 制造商:Olimex Ltd. 产品:Development Boards 工具用于评估:MSP430F5510 核心:MSP430 接口类型:JTAG, USB 工作电源电压:5 V
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*