参数资料
型号: MSP430F2101IDWR
厂商: TEXAS INSTRUMENTS INC
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PDSO20
封装: GREEN, PLASTIC, SOIC-20
文件页数: 57/57页
文件大小: 1276K
代理商: MSP430F2101IDWR
MSP430x21x1
MIXED SIGNAL MICROCONTROLLER
SLAS439D -- SEPTEMBER 2004 -- REVISED SEPTEMBER 2010
9
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
peripherals
Peripherals are connected to the CPU through data, address, and control busses and can be handled using
all instructions. For complete module descriptions, refer to the MSP430x2xx Family User’s Guide.
oscillator and system clock
The clock system is supported by the basic clock module that includes support for a 32768-Hz watch crystal
oscillator, an internal digitally-controlled oscillator (DCO) and a high frequency crystal oscillator. The basic clock
module is designed to meet the requirements of both low system cost and low-power consumption. The internal
DCO provides a fast turn-on clock source and stabilizes in less than 1 s. The basic clock module provides the
following clock signals:
D
Auxiliary clock (ACLK), sourced from a 32768-Hz watch crystal or a high frequency crystal.
D
Main clock (MCLK), the system clock used by the CPU.
D
Sub-Main clock (SMCLK), the sub-system clock used by the peripheral modules.
DCO CALIBRATION DATA
(PROVIDED FROM FACTORY IN FLASH INFO MEMORY SEGMENT A)
DCO FREQUENCY
CALIBRATION
REGISTER
SIZE
ADDRESS
1MHz
CALBC1_1MHZ
byte
010FFh
CALDCO_1MHZ
byte
010FEh
8MHz
CALBC1_8MHZ
byte
010FDh
CALDCO_8MHZ
byte
010FCh
12 MHz
CALBC1_12MHZ
byte
010FBh
CALDCO_12MHZ
byte
010FAh
16 MHz
CALBC1_16MHZ
byte
010F9h
CALDCO_16MHZ
byte
010F8h
brownout
The brownout circuit is implemented to provide the proper internal reset signal to the device during power on
and power off.
digital I/O
There are two 8-bit I/O ports implemented—ports P1 and P2:
D
All individual I/O bits are independently programmable.
D
Any combination of input, output, and interrupt conditions is possible.
D
Edge-selectable interrupt input capability for all the eight bits of port P1 and P2.
D
Read/write access to port-control registers is supported by all instructions.
D
Each I/O has an individually programmable pull--up/pull--down resistor.
WDT+ watchdog timer
The primary function of the watchdog timer (WDT+) module is to perform a controlled system restart after a
software problem occurs. If the selected time interval expires, a system reset is generated. If the watchdog
function is not needed in an application, the module can be configured as an interval timer and can generate
interrupts at selected time intervals.
相关PDF资料
PDF描述
MC9S12P32CQKR 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP80
MC908QB8VDTE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
MC908GR32AMFAE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48
MC908GZ48CFJR2 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
MC908GZ48CFUR2 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
MSP430F2101IPW 功能描述:16位微控制器 - MCU 16-bit Ult-Lo-Pwr 1kB Flash 128B RAM RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MSP430F2101IPWR 功能描述:16位微控制器 - MCU 16-bit Ult-Lo-Pwr 1kB Flash 128B RAM RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MSP430F2101IRGE 制造商:TI 制造商全称:Texas Instruments 功能描述:MIXED SIGNAL MICROCONTROLLER
MSP430F2101IRGER 功能描述:16位微控制器 - MCU 16-bit Ult-Lo-Pwr 1kB Flash 128B RAM RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MSP430F2101IRGET 功能描述:16位微控制器 - MCU 16-bit Ult-Lo-Pwr 1kB Flash 128B RAM RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT