参数资料
| 型号： | MX7705EUE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/33页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 2CH 16-TSSOP |
| 产品培训模块： | MAX11200 ADC Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 位数： | 16 |
| 采样率（每秒）： | 500 |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 755mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 输入数目和类型： | 2 个差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
MX7705
Modulator
The MX7705 performs analog-to-digital conversions
using a single-bit, 2nd-order, switched-capacitor,
sigma-delta modulator. The sigma-delta modulation
converts the input signal into a digital pulse train whose
average duty cycle represents the digitized signal infor-
mation. A single comparator within the modulator quan-
tizes the input signal at a much higher sample rate than
the bandwidth of the input.
The MX7705 modulator provides 2nd-order frequency
shaping of the quantization noise resulting from the sin-
gle-bit quantizer. The modulator is fully differential for
maximum signal-to-noise ratio and minimum suscepti-
bility to power-supply and common-mode noise. A sin-
gle-bit data stream is then presented to the digital filter
for processing to remove the frequency-shaped quanti-
zation noise.
The modulator sampling frequency is fCLKIN / 128,
regardless of gain, where fCLKIN (CLKDIV = 0) is the
frequency of the signal at CLKIN.
Digital Filtering
The MX7705 contains an on-chip, digital lowpass filter
that processes the 1-bit data stream from the modulator
using a SINC3 (sinx/x)3 response. The SINC3 filter has a
settling time of three output data periods.
Filter Characteristics
Figure 6 shows the filter frequency response. The
SINC3 characteristic -3dB cutoff frequency is 0.262
times the first-notch frequency. This results in a cutoff
frequency of 15.72Hz for a first filter-notch frequency of
60Hz (output data rate of 60Hz). The response shown
in Figure 5 is repeated at either side of the digital filter’s
sample frequency, fM (fM = 19.2kHz for 60Hz output
data rate), and at either side of the related harmonics
(2fM, 3fM, etc.).
The output data rate for the digital filter corresponds with
the positioning of the first notch of the filter’s frequency
response. Therefore, for the plot in Figure 6, where the first
notch of the filter is 60Hz, the output data rate is 60Hz. The
notches of the SINC3 filter are repeated at multiples of the
first notch frequency. The SINC3 filter provides an attenua-
tion of better than 100dB at these notches.
Determine the cutoff frequency of the digital filter by load-
ing the appropriate values into the CLK, FS0, and FS1
bits in the clock register (Table 13). Programming a differ-
ent cutoff frequency with FS0 and FS1 changes the fre-
quency of the notches, but it does not alter the profile of
the frequency response.
For step changes at the input, allow a settling time
before valid data is read. The settling time depends on
the output data rate chosen for the filter. The worst-
case settling time of a SINC3 filter for a full-scale step
input is four times the output data period. By synchro-
nizing the step input using FSYNC, the settling time
reduces to three times the output data period. If FSYNC
is high during the step input, the filter settles in three
times the output data period after FSYNC falls low.
Analog Filtering
The digital filter does not provide any rejection close to
the harmonics of the modulator sample frequency. Due
to the high oversampling ratio of the MX7705, these
bands occupy only a small fraction of the spectrum and
most broadband noise is filtered. The analog filtering
requirements in front of the MX7705 are reduced com-
pared to a conventional converter with no on-chip filtering.
In addition, the devices provide excellent common-mode
rejection of 90db to reduce the common-mode noise sus-
ceptibility.
Additional filtering prior to the MX7705 eliminates
unwanted frequencies the digital filter does not reject.
Use additional filtering to ensure that differential noise
signals outside the frequency band of interest do not
saturate the analog modulator.
If passive components are in the path of the analog
inputs when the device is in unbuffered mode, ensure
the source impedance is low enough (Figure 2) not to
introduce gain errors in the system. This significantly
limits the amount of passive anti-aliasing filtering that
can be applied in front of the MX7705 in unbuffered
mode. In buffered mode, large source impedance
causes a small DC-offset error, which can be removed
by calibration.
16-Bit, Low-Power, 2-Channel,
Sigma-Delta ADC
20
______________________________________________________________________________________
-160
-120
-140
-100
-80
-60
-20
-40
0
406080
20
100 120 140 160 180 200
FREQUENCY (Hz)
GAIN
(dB)
fCLKIN = 2.4576MHz
CLK = 1
FS1 = 0
FS0 = 1
fN = 60Hz
Figure 6. Frequency Response of the SINC3 Filter (Notch at 60Hz)
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B6Z-IU-F3 | CONVERTER MOD DC/DC 2V 80W |
| VI-B6Z-IU-F2 | CONVERTER MOD DC/DC 2V 80W |
| MAX1185ECM/V+ | IC ADC 10BIT 20MSPS DL LP 48TQFP |
| MS27497T16F99PB | CONN RCPT 23POS WALL MNT W/PINS |
| IDT723644L12PF8 | IC FIFO SYNC 2048X36 128QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MX7705EUE+ | 功能描述:模数转换器 - ADC 16-Bit 2Ch Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MX7705EUE+T | 功能描述:模数转换器 - ADC 16-Bit 2Ch Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MX7705EUE-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MX7705EWE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MX7705EWE+ | 功能描述:模数转换器 - ADC 16-Bit 2Ch Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。