- 您现在的位置：买卖IC网 > PDF目录189003 > NAND08GR3B3BZC6E (STMICROELECTRONICS) 1G X 8 FLASH 1.8V PROM, 35 ns, PBGA63 PDF资料下载
参数资料
| 型号： | NAND08GR3B3BZC6E |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | PROM |
| 英文描述： | 1G X 8 FLASH 1.8V PROM, 35 ns, PBGA63 |
| 封装： | 9.50 X 12 MM, 1.40 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, LFBGA-63 |
| 文件页数： | 15/59页 |
| 文件大小： | 998K |
| 代理商： | NAND08GR3B3BZC6E |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
NAND512-B, NAND01G-B, NAND02G-B, NAND04G-B, NAND08G-B
22/59
Page Program
The Page Program operation is the standard oper-
ation to program data to the memory array. Gener-
ally, data is programmed sequentially, however
the device does support Random Input within a
page.
The memory array is programmed by page, how-
ever partial page programming is allowed where
any number of Bytes (1 to 2112) or Words (1 to
1056) can be programmed.
The maximum number of consecutive partial page
program operations allowed in the same page is
eight. After exceeding this a Block Erase com-
mand must be issued before any further program
operations can take place in that page.
Sequential Input. To input data sequentially the
addresses must be sequential and remain in one
block.
For Sequential Input each Page Program opera-
tion consists of five steps (see Figure 12.):
1.
one bus cycle is required to setup the Page
Program (Sequential Input) command (see
2.
four or five bus cycles are then required to
input the program address (refer to Table 6.
and Table 7.)
3.
the data is then loaded into the Data Registers
4.
one bus cycle is required to issue the Page
Program confirm command to start the P/E/R
Controller. The P/E/R will only start if the data
has been loaded in step 3.
5.
the P/E/R Controller then programs the data
into the array.
Random Data Input. During a Sequential Input
operation, the next sequential address to be pro-
grammed can be replaced by a random address,
by issuing a Random Data Input command. The
following two steps are required to issue the com-
mand:
1.
one bus cycle is required to setup the Random
Data Input command (see Table 10.)
2.
two bus cycles are then required to input the
new column address (refer to Table 6.)
Random Data Input can be repeated as often as
required in any given page.
Once the program operation has started the Sta-
tus Register can be read using the Read Status
Register command. During program operations
the Status Register will only flag errors for bits set
to '1' that have not been successfully programmed
to '0'.
During the program operation, only the Read Sta-
tus Register and Reset commands will be accept-
ed, all other commands will be ignored.
Once the program operation has completed the P/
E/R Controller bit SR6 is set to ‘1’ and the Ready/
Busy signal goes High.
The device remains in Read Status Register mode
until another valid command is written to the Com-
mand Interface.
Figure 12. Page Program Operation
I/O
RB
Address Inputs
SR0
ai08659
Data Input
10h
70h
80h
Page Program
Setup Code
Confirm
Code
Read Status Register
Busy
tBLBH2
(Program Busy time)
相关PDF资料 |
PDF描述 |
|---|---|
| NAND08GR3B3CN1E | 1G X 8 FLASH 1.8V PROM, 35 ns, PDSO48 |
| NAND08GW4B2CZC1F | 512M X 16 FLASH 3V PROM, 35 ns, PBGA63 |
| NAND08GW4B3AZC6 | 512M X 16 FLASH 3V PROM, 35 ns, PBGA63 |
| NAND08GW4B3BN1T | 512M X 16 FLASH 3V PROM, 35 ns, PDSO48 |
| NAND08GW4B3BN6E | 512M X 16 FLASH 3V PROM, 35 ns, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NAND08GR3B4CZL6E | 制造商:Micron Technology Inc 功能描述:NAND - Trays |
| NAND08GR3B4CZL6F | 制造商:Micron Technology Inc 功能描述:NAND - Tape and Reel |
| NAND08GW3B2AN6E | 功能描述:闪存 4 GBit 2112 Byte 1056 WP 1.8v/3v RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND08GW3B2AN6F | 功能描述:闪存 4 GB 2112B 1056 Word Pg 1.8V/3V RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND08GW3B2BN6E | 制造商:Micron Technology Inc 功能描述:NAND & S.MEDIA FLASH - Trays |
发布紧急采购，3分钟左右您将得到回复。