- 您现在的位置：买卖IC网 > PDF目录189001 > NAND512W3A0AN1 (NUMONYX) 64M X 8 FLASH 3V PROM, 35 ns, PDSO48 PDF资料下载
参数资料
| 型号： | NAND512W3A0AN1 |
| 厂商： | NUMONYX |
| 元件分类： | PROM |
| 英文描述： | 64M X 8 FLASH 3V PROM, 35 ns, PDSO48 |
| 封装： | 12 X 20 MM, PLASTIC, TSOP-48 |
| 文件页数： | 20/57页 |
| 文件大小： | 916K |
| 代理商： | NAND512W3A0AN1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
27/57
NAND128-A, NAND256-A, NAND512-A, NAND01G-A
Block Erase
Erase operations are done one block at a time. An
erase operation sets all of the bits in the ad-
dressed block to ‘1’. All previous data in the block
is lost.
An erase operation consists of three steps (refer to
1.
One bus cycle is required to setup the Block
Erase command.
2.
Only three bus cycles for 512Mb and 1Gb
devices, or two for 128Mb and 256Mb devices
are required to input the block address. The
first cycle (A0 to A7) is not required as only
addresses A14 to A26 (highest address
depends on device density) are valid, A9 to
A13 are ignored. In the last address cycle I/O2
to I/O7 must be set to VIL.
3.
One bus cycle is required to issue the confirm
command to start the P/E/R Controller.
Once the erase operation has completed the Sta-
tus Register can be checked for errors.
Figure 19. Block Erase Operation
Reset
The Reset command is used to reset the Com-
mand Interface and Status Register. If the Reset
command is issued during any operation, the op-
eration will be aborted. If it was a program or erase
operation that was aborted, the contents of the
memory locations being modified will no longer be
valid as the data will be partially programmed or
erased.
If the device has already been reset then the new
Reset command will not be accepted.
The Ready/Busy signal goes Low for tBLBH4 after
the Reset command is issued. The value of tBLBH4
depends on the operation that the device was per-
forming when the command was issued, refer to
Table 21. for the values.
I/O
RB
Block Address
Inputs
SR0
ai07593
D0h
70h
60h
Block Erase
Setup Code
Confirm
Code
Read Status Register
Busy
tBLBH3
(Erase Busy time)
相关PDF资料 |
PDF描述 |
|---|---|
| NAND512W3A0CZB6 | 64M X 8 FLASH 3V PROM, 35 ns, PBGA55 |
| NAND128W4A0AZA1F | 8M X 16 FLASH 3V PROM, 35 ns, PBGA55 |
| NAND128W4A2BZA1F | 8M X 16 FLASH 3V PROM, 35 ns, PBGA55 |
| NAND512W3A0AZA1E | 64M X 8 FLASH 3V PROM, 35 ns, PBGA63 |
| NAND512W3A2BN1E | 64M X 8 FLASH 3V PROM, 35 ns, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NAND512W3A0AN6 | 功能描述:闪存 NAND & S.MEDIA FLASH RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND512W3A0AN6E | 功能描述:闪存 2.7-3.6V 512M(64Mx8) RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND512W3A0AN6F | 制造商:Micron Technology Inc 功能描述:FLASH PARALLEL 3V/3.3V 512MBIT 64MX8 12US 48TSOP - Tape and Reel |
| NAND512W3A0AV6E | 功能描述:IC FLASH 512MBIT 48WSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:576 系列:- 格式 - 存储器:闪存 存储器类型:闪存 - NAND 存储容量:512M（64M x 8） 速度:- 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 其它名称:497-5040 |
| NAND512W3A2BE06 | 制造商:STMicroelectronics 功能描述:512 MBIT NAND FLASH MEMORY WAFER |
发布紧急采购，3分钟左右您将得到回复。