- 您现在的位置：买卖IC网 > PDF目录11719 > NCN6000DTB (ON Semiconductor)IC SMART CARD COMPACT 20-TSSOP PDF资料下载
参数资料
| 型号： | NCN6000DTB |
| 厂商： | ON Semiconductor |
| 文件页数： | 15/36页 |
| 文件大小： | 0K |
| 描述： | IC SMART CARD COMPACT 20-TSSOP |
| 产品变化通告： | Product Obsolescence 01/Jul/2009 |
| 标准包装： | 75 |
| 应用： | ATM 终端，气泵，ISM |
| 接口： | 微控制器 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
NCN6000
http://onsemi.com
22
Vbat Supply Voltage Monitoring
The builtin comparator, associated with the band gap
reference, continuously monitors the +Vbat input. During
the start up, all the NCN6000 functions are deactivated and
no data transfer can take place. When the +Vbat voltage rises
above 2.35 V (typical), the chip is activated and all the
functions becomes available. The typical behavior is
provided here after Figure 16. At this point, the internal
Power On Reset signal is activated (not accessible
externally) and all the logic signals are forced into the states
as defined by Table 3.
If the +Vbat voltage drops below 2.25 V (typical) during
the operation, the NCN6000 generate a Power Down
sequence and is forced in a no operation mode. The builtin
100 mV (typical) hysteresis avoids unstable operation when
the battery voltage slowly varies around the 2.30 V.
On the other hand, the microcontroller can read the
STATUS signal, pin 5, to control the state of the battery prior
to launch either a NCN6000 programming or an ATR
sequence (Table 4).
2.80 V
Figure 16. Typical Vbat Monitoring
Vbat
2.35 V
2.25 V
3.30 V
Vbat_OK
Vbat STATUS
Note: Drawing is not to scale and voltages are typical.
See specifications data for details.
DCDC Converter Operation
The builtin DCDC converter is based on a modified
boost structure to cover the full battery and card operating
voltage range. The builtin battery voltage monitor provides
an automatic system to accommodate the mode of operation
whatever be the Vbat and CRD_VCC voltages. Comparator
U3/Figure 17 tracks the two voltages and set up the
operating mode accordingly.
U2
+
U3
Vref
+
MOS Drive
Substrat Bias
U1
PWR_ON
3 V/ 5 V
Overload
VCC_OK
R1
1R
Current Sense
20
19
18
15
17
Vbat
L2
22
mH
Lout_L
Lout_H
+
GND
CRD_VCC
C1
GND
Vout_3_5
Vref_3/5 V
Voltage Regulation
Vbat
Q3
Q1
Q2
GND
Vbat
Vbat/VCC Comparator
NMOS Gate Drive
PMOS Gate Drive
LOGIC
CONTROL
GND
PWR_GND
GND
Figure 17. Basic DCDC Structure
+
R2
R3
R4
Active Pull Down
GND
Q4
相关PDF资料 |
PDF描述 |
|---|---|
| MS3116F20-41P | CONN PLUG 41POS STRAIGHT W/PINS |
| V110B5H150B3 | CONVERTER MOD DC/DC 5V 150W |
| C8051T604-GS | IC 8051 MCU 2K-EEPROM 14-SOIC |
| V110B48H150BG3 | CONVERTER MOD DC/DC 48V 150W |
| V110B48H150BF2 | CONVERTER MOD DC/DC 48V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCN6000DTBG | 功能描述:输入/输出控制器接口集成电路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| NCN6000DTBR2 | 功能描述:输入/输出控制器接口集成电路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| NCN6000DTBR2G | 功能描述:输入/输出控制器接口集成电路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| NCN6001 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
发布紧急采购，3分钟左右您将得到回复。