- 您现在的位置：买卖IC网 > PDF目录11719 > NCN6000DTB (ON Semiconductor)IC SMART CARD COMPACT 20-TSSOP PDF资料下载
参数资料
| 型号： | NCN6000DTB |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/36页 |
| 文件大小： | 0K |
| 描述： | IC SMART CARD COMPACT 20-TSSOP |
| 产品变化通告： | Product Obsolescence 01/Jul/2009 |
| 标准包装： | 75 |
| 应用： | ATM 终端，气泵，ISM |
| 接口： | 微控制器 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
NCN6000
http://onsemi.com
17
Transaction Mode
During the transaction mode, the NCN6000 maintains
power supply and clock signal to the card. All the signal
levels related with the card are translated as necessary to
cope with the MPU and the card.
The DCDC converter status and the Vbat state can be
monitored on the STATUS by using the A0 and A1 logic
Transaction Mode
Logic Conditions:
Card Output:
CS
= L
PWR_ON = H
A0
= H
A1
= H
PGM
= H
I/O
= DATA
TRANSFER
RESET
= H/L
STATUS
= L/H DCDC
status: Fail/Pass?
CRD_VCC = 3.0 or 5.0 V
CRD_CLK = CLOCK
CRD_RST = H/L
CRD_IO
= DATA
TRANSFER
To make sure the data are not polluted by power losses, it
is recommended to check the state of CRD_VCC before
launching a new data transaction. Since CS = L, this is
achieved by forcing bits A0 and A1 according to Table 4, and
reading the STATUS pin 5.
Idle Mode
The idle mode is used when a card is powered up
(CRD_VCC = Vcc), without communication on going.
Idle Mode
Logic Conditions:
Card Output:
CS
= L
PWR_ON = H
A0
= H
A1
= H
PGM
= H
I/O
= Z
RESET
= H
STATUS
= L/H according
to the internal
register results
CRD_VCC = 3.0 or 5.0 V
CRD_CLK = CLOCK active or
L or H
CRD_RST = H
CRD_IO
= Z
In addition, the CRD_CLK signal can be stopped, as
consumption of the external smart card, leaving CRD_VCC
active.
Power Down Operation
The power down mode can be initiated by either the
external MPU (pulling PWR_ON = L) or by one of the
internal error condition (CRD_VCC overload or Vbat Low).
The communication session is terminated immediately,
according to the ISO78163 sequence. On the other hand,
the MPU can run the Standby mode by forced CS = H.
When the card is extracted, the interface shall detect the
operation and run the Power Shut Off of the card as
described by the ISO/CEI 78163 sequence depicted here
after:
ISO78163 sequence:
Force RST to Low
Force CLK to Low, unless it is already in this state
Force CRD_IO to Low
Shut Off the CRD_VCC supply
Since the internal digital filter is activated for any card
insertion or extraction, the physical power sequence will be
activated 150
ms maximum after the card has been extracted.
Of course, such a delay does not exist when the MPU launch
the power down intentionally.
The time delay between each negative going signal is
500 ns typical (Figure 10).
相关PDF资料 |
PDF描述 |
|---|---|
| MS3116F20-41P | CONN PLUG 41POS STRAIGHT W/PINS |
| V110B5H150B3 | CONVERTER MOD DC/DC 5V 150W |
| C8051T604-GS | IC 8051 MCU 2K-EEPROM 14-SOIC |
| V110B48H150BG3 | CONVERTER MOD DC/DC 48V 150W |
| V110B48H150BF2 | CONVERTER MOD DC/DC 48V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCN6000DTBG | 功能描述:输入/输出控制器接口集成电路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| NCN6000DTBR2 | 功能描述:输入/输出控制器接口集成电路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| NCN6000DTBR2G | 功能描述:输入/输出控制器接口集成电路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| NCN6001 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
发布紧急采购，3分钟左右您将得到回复。