- 您现在的位置：买卖IC网 > PDF目录17227 > NCP1216AFORWEVB (ON Semiconductor)BOARD EVAL NCP1216A DC/DC CONV PDF资料下载
参数资料
| 型号： | NCP1216AFORWEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/18页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL NCP1216A DC/DC CONV |
| 产品变化通告： | 1Q2012 Discontinuation 30/Mar/2012 |
| 设计资源： | NCP1216AFORWEVB Schematic NCP1216AFORWEVB Bill of Materials NCP1216AFORWEVB Test Procedure NCP1216AFORWEVB Gerber Zip |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | NCP1216AFORWEVB-ND NCP1216AFORWEVBOS |
NCP1216, NCP1216A
APPLICATION INFORMATION
Introduction
The NCP1216 implements a standard current mode
architecture where the switch ? off event is dictated by the
peak current setpoint. This component represents the ideal
candidate where low part count is the key parameter,
particularly in low ? cost AC ? DC adapters, TV power
supplies etc. Due to its high ? performance High ? Voltage
technology, the NCP1216 incorporates all the necessary
components normally needed in UC384X based supplies:
timing components, feedback devices, low ? pass filter and
self ? supply. This later point emphasizes the fact that ON
Semiconductor’s NCP1216 does NOT need an auxiliary
winding to operate: the product is naturally supplied from
the high ? voltage rail and delivers a V CC to the IC. This
system is called the Dynamic Self ? Supply (DSS):
Dynamic Self ? Supply (DSS): Due to its Very High
Voltage Integrated Circuit (VHVIC) technology,
ON Semiconductor ’s NCP1216 allows for a direct pin
connection to the high ? voltage DC rail. A dynamic current
source charges up a capacitor and thus provides a fully
independent V CC level to the NCP1216. As a result, there is
no need for an auxiliary winding whose management is
always a problem in variable output voltage designs (e.g.
battery chargers).
Adjustable Skip Cycle Level: By offering the ability to tailor
the level at which the skip cycle takes place, the designer can
make sure that the skip operation only occurs at low peak
current. This point guarantees a noise ? free operation with
cheap transformers. Skip cycle offers a proven mean to
reduce the standby power in no or light loads situations.
Internal Frequency Dithering for Improved EMI
Signature: By modulating the internal switching frequency
with the DSS V CC ripple, natural energy spread appears and
softens the controller ’s EMI signature.
Wide Switching ? Frequency Offered with Different
Options (65 kHz ? 100 kHz ? 133 kHz): Depending on the
application, the designer can pick up the right device to help
reducing magnetics or improve the EMI signature before
reaching the 150 kHz starting point.
Ramp Compensation: By inserting a resistor between the
Current Sense (CS) pin and the actual sense resistor, it
becomes possible to inject a given amount of ramp
compensation since the internal sawtooth clock is routed to
the CS pin. Sub ? harmonic oscillations in Continuous
Conduction Mode (CCM) can thus be compensated via a
Over Current Protection (OCP): By continuously
monitoring the FB line activity, NCP1216 enters burst mode
as soon as the power supply undergoes an overload. The
device enters a safe low power operation, which prevents
from any lethal thermal runaway. As soon as the default
disappears, the power supply resumes operation. Unlike
other controllers, overload detection is performed
independently of any auxiliary winding level. In presence of
a bad coupling between both power and auxiliary windings,
the short circuit detection can be severely affected. The DSS
naturally shields you against these troubles.
Wide Duty ? Cycle Operation: Wide mains operation requires
a large duty ? cycle excursion. The NCP1216 can go up to 75%
typically. For Continuous Conduction Mode (CCM)
applications, the internal ramp compensation lets you fight
against sub ? harmonic oscillations.
Low Standby Power: If SMPS naturally exhibit a good
efficiency at nominal load, they begin to be less efficient
when the output power demand diminishes. By skipping
unnecessary switching cycles, the NCP1216 drastically
reduces the power wasted during light load conditions. In
no ? load conditions, the NPC1216 allows the total standby
power to easily reach next International Energy Agency
(IEA) recommendations.
No Acoustic Noise While Operating: Instead of skipping
cycles at high peak currents, the NCP1216 waits until the
peak current demand falls below a user ? adjustable 1/3 of the
maximum limit. As a result, cycle skipping can take place
without having a singing transformer, one can thus select
cheap magnetic components free of noise problems.
External MOSFET Connection: By leaving the external
MOSFET external to the IC, you can select avalanche proof
devices, which in certain cases (e.g. low output powers), let
you work without an active clamping network. Also, by
controlling the MOSFET gate signal flow; you have an
option to slow down the device commutation, therefore
reducing the amount of ElectroMagnetic Interference
(EMI).
SPICE Model: A dedicated model to run transient
cycle ? by ? cycle simulations is available but also an
averaged version to help you closing the loop.
Ready ? to ? use templates can be downloaded in OrCAD’s
PSpice and INTUSOFT’s IsSpice from ON Semiconductor
web site, in the NCP1216 related section.
single resistor.
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| 594D337X96R3C8T | CAP TANT 330UF 6.3V 10% 2812 |
| GI1402HE3/45 | DIODE 8A 100V 35NS SGL TO220-2 |
| GEC17DRYH-S13 | CONN EDGECARD 34POS .100 EXTEND |
| EBM15DCTD-S288 | CONN EDGECARD 30POS .156 EXTEND |
| HCM06DSEN-S243 | CONN EDGECARD 12POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1216AFORWGEVB | 功能描述:BOARD EVAL NCP1216A 35W RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:* 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| NCP1216AP100 | 功能描述:开关变换器、稳压器与控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| NCP1216AP100G | 功能描述:电流型 PWM 控制器 Current Mode PWM w/50% Duty Cycle Max RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1216AP133 | 功能描述:电流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1216AP133G | 功能描述:电流型 PWM 控制器 Current Mode PWM w/50% Duty Cycle Max RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。