- 您现在的位置：买卖IC网 > PDF目录19650 > NCP1351BPG (ON Semiconductor)IC CTRLR PWM PROG CM OTP 8DIP PDF资料下载
参数资料
| 型号： | NCP1351BPG |
| 厂商： | ON Semiconductor |
| 文件页数： | 15/27页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM PROG CM OTP 8DIP |
| 标准包装： | 50 |
| 输出隔离： | 隔离 |
| 频率范围： | 调节 |
| 输入电压： | 9.5 V ~ 28 V |
| 工作温度： | -25°C ~ 125°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
NCP1351
At this point, the current is fully compressed and remains
frozen. To further decrease the transmitted power, the
frequency does not have other choice than going down.
CS Current
270 m A
FAULT
Fault detection
The fault detection circuitry permanently observes the FB
current, as shown on Figure 19. When the feedback current
decreases below 40 m A, an external capacitor is charged by
a 11.7 m A source. As the voltage rises, a comparator detects
when it reaches 5 V typical. Upon detection, there can be
two different scenarios:
1. A version: the circuit immediately latches-off and
remains latched until the voltage on the current
into the V CC pin drops below a few m A. The latch
70 m A
(A, B versions)
is made via an internal SCR circuit who holds
VCC to around 6 V when fired. As long as the
current flowing through this latch is above a few
m A, the circuit remains locked-out. When the user
unplugs the converter, the V CC current falls down
and resets the latch.
40 m A 60 m A 80 m A FB Current
Figure 16. The NCP1351 Peak Current Compression
Scheme
Looking to the data-sheet specifications, the maximum
peak current is set to 270 m A whereas the compressed
current goes down to 70 m A. The NCP1351 can thus be
considered as a multi operating mode circuit:
? Real fixed peak current / variable frequency mode for
FB current below 60 m A.
? Then maximum peak current decreases to I CS,min over a
narrow linear range of I FB (to avoid instability created
by a discrete jump from I CS,max to I CS,min ), between
60 m A and 80 m A.
? Then if I FB keeps on increasing, in a real fixed peak
current/variable frequency mode with reduced peak
current
For biasing purposes and noise immunity improvements,
we recommend to wire a pulldown resistor and a capacitor
in parallel from the FB pin to the controller ground
(Figure 17). Please keep these elements as close as possible
to the circuit. The pulldown resistor increases the
optocoupler current but also plays a role in standby. We
found that a 2.5 k W resistor was giving a good tradeoff
between optocoupler operating current (internal pole
2. B version: the circuit stops its output pulses and
the auxiliary V CC decreases via the controller own
consumption ( ≈ 600 m A). When it touches the
V CC(min) point, the circuit re-starts and attempts to
crank the power supply. If it fails again, an hiccup
mode takes place (Figure 18).
3. C version: this version includes the dual Over
Current Protection (OCP) level. When the
switching frequency imposed by the feedback loop
reaches around 50% of the maximum value set by
the Ct capacitor, the timer starts to count down. If
the fault disappears, the timer is reset. When the
fault is finally confirmed, the controller latches off
as the A version.
4. D version: this version includes the dual Over
Current Protection (OCP) level. When the
switching frequency imposed by the feedback loop
reaches around 50% of the maximum value set by
the Ct capacitor, the timer starts to count down. If
the fault disappears, the timer is reset. When the
fault is finally confirmed, the controller enters
auto-recovery mode, as with the B version.
V CC
position) and standby power.
V CC
V drv
FB
R1
2.5k
C1
100nF
Figure 18. Hiccup Occurs with the B Version Only,
the A Version Being Latched
Figure 17. The Recommended Feedback
Arrangement Around the FB Pin
The duty-burst in fault is around 7% in this particular
case.
http://onsemi.com
15
相关PDF资料 |
PDF描述 |
|---|---|
| TAP685K035HSC | CAP TANT 6.8UF 35V 10% RADIAL |
| TAP685K035HCD | CAP TANT 6.8UF 35V 10% RADIAL |
| LC4384C-5FTN256I | IC CPLD 384MACROCELLS 256FTBGA |
| RS-1215S/H3 | CONV DC/DC 2W 9-18VIN 15VOUT |
| VE-BT0-CY-F4 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1351CDR2G | 功能描述:电流型 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1351CPG | 功能描述:电流型 PWM 控制器 VRIABLE OFF TM CNTRL RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1351DDR2G | 功能描述:电流型 PWM 控制器 PWM CONTROLLER RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1351DPG | 功能描述:电流型 PWM 控制器 VRIABLE OFF TM CNTRL RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1351LEDGEVB | 功能描述:电源管理IC开发工具 20 W CONSTANT CUR LED DRV RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。