- 您现在的位置：买卖IC网 > PDF目录19847 > NCP1377BDR2G (ON Semiconductor)IC CTRLR PWM SMPS CM UVLO 8SOIC PDF资料下载
参数资料
| 型号： | NCP1377BDR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 10/17页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM SMPS CM UVLO 8SOIC |
| 标准包装： | 1 |
| 输出隔离： | 隔离 |
| 频率范围： | 300kHz |
| 输入电压： | 8.2 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 标准包装 |
| 其它名称： | NCP1377BDR2GOSDKR |
NCP1377, NCP1377B
An internal timer prevents any restart within 8.0 m s
further to the driver going ? low transition for NCP1377,
and 3.0 m s for NCP1377B. This prevents the switching
frequency to exceed (1.0/T ON + T blank ) but also avoid false
leakage inductance tripping at turn ? off. In some cases, the
leakage inductance kick is so energetic, that a slight
filtering is necessary.
The NCP1377 demagnetization detection pad features a
for NCP1377 and 1.5 m s for NCP1377B guarantees a clean
plateau, providing that the leakage inductance ringing has
been fully damped. If this would not be the case, the
designer should install a small RC damper across the
transformer primary inductance connections. Figure 24
shows where the sampling occurs on the auxiliary winding.
specific component arrangement as detailed by Figure 22.
In this picture, the zener diodes network protect the IC
against any potential ESD discharge that could appear on
the pins. The first ESD diode connected to the pad, exhibits
a parasitic capacitance. When this parasitic capacitance
8.0
6.0
SAMPLING HERE
(10 pF typically) is combined with Rdem, a restart delay
is created and the possibility to switch right in the
drain ? source wave exists. This guarantees QR operation
with all the associated benefits (low EMI, no turn ? on
losses etc.). Rdem should be calculated to limit the
maximum current flowing through pin 1 to less than
+3.0 mA/ ? 2.0 mA: If during turn ? on, the auxiliary
winding delivers 30 V (at the highest line level), then the
minimum Rdem value is defined by: 30 + 0.7/3.0 mA =
10.2 k W . This value will be further increased, e.g. to
introduce a restart delay and also a slight filtering in case
of high leakage energy.
Figure 23 portrays a typical Vds shot at nominal output
power.
400
300
200
100
0
Figure 23. The NCP1377 Operates in
Borderline/Critical Operation
Overvoltage Protection
The overvoltage protection works by sampling the
plateau voltage after the turn ? off sequence. A 4.5 m s delay
4.0
2.0
4.5 m s
0
Figure 24. A Voltage Sample is Taken 4.5 m s
After the Turn ? Off Sequence
When an OVP condition has been detected, the
NCP1377 enters a latchoff phase and stops all switching
operations. The controller stays fully latched in this
position and the startup source being still active, it keeps
the Vcc going up and down between 12.5 V and 5.6 V. This
state lasts until the Vcc is cycled down to 4.0 V, e.g. when
the user unplugs the power supply from the mains outlet.
By default, the OVP comparator is biased to a 5.0 V
reference level and pin1 is routed via a divide by a 1.44
network. As a result, when Vpin1 reaches 7.2 V, the OVP
comparator is triggered. The threshold can thus be adjusted
by either modifying the power winding to auxiliary
winding turn ratios to match this 7.2 V level or insert a
resistor from pin1 to ground to cope with your design
requirement.
Latching Off the NCP1377
In certain cases, it can be very convenient to externally
shut down permanently the NCP1377 via a dedicated
signal, e.g. coming from a temperature sensor (Figure 25).
The reset occurs when the user unplugs the power supply
from the mains outlet. To trigger the latchoff by an external
signal, a simple PNP transistor can do the work, as
Figure 26 shows.
http://onsemi.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BW0-CY-F3 | CONVERTER MOD DC/DC 5V 50W |
| EPM570M100C5N | IC MAX II CPLD 570 LE 100-MBGA |
| VE-BW0-CY-F2 | CONVERTER MOD DC/DC 5V 50W |
| EPM570T100C5N | IC MAX II CPLD 570 LE 100-TQFP |
| VE-BW0-CY-F1 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCP1377BDR2G-CUT TAPE | 制造商:ON 功能描述:NCP1377 Series 18 V 300 kHz Surface Mount PWM Current-Mode Controller - SOIC-8 |
| NCP1377BP | 功能描述:电流型 PWM 控制器 Quasi Resonant RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1377BPG | 功能描述:电流型 PWM 控制器 Quasi Resonant Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1377D1R2G | 功能描述:电流型 PWM 控制器 Quasi Resonant Current Mode PWM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| NCP1377DR2 | 功能描述:开关变换器、稳压器与控制器 Quasi Resonant RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。